Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Small green circuit board with mSATA slot and SATA connectors

SMUGDESK

SMUGDESK 5cm LowProfile mSATA to SATA Adapter 2.5

SKU CH-4P1P-3HRF6

Converts an mSATA SSD into a 2.5 SATA drive for laptop storage upgrades

  • Converts mSATA SSD to 2.5 SATA for easy notebook storage upgrade
  • Compact 5cm low-profile PCB fits tight laptop chassis without space conflicts
  • SATA 6Gbps bandwidth preserves original SSD read-write performance
  • Plug-and-play installation requires no drivers or software
  • Reuses spare mSATA drive to replace mechanical HDD and boost responsiveness

Compact mSATA Adapter for Notebook Upgrades

This 5 cm low-profile board converts a standard mSATA SSD into a 2.5 inch SATA device. It is built for laptop and notebook owners who want to repurpose an existing mSATA drive as an internal storage upgrade. The bare PCB design fits tight chassis spaces without a metal enclosure. Installation is plug-and-play with no driver required.

SATA 3 Bandwidth and Backward Compatibility Limits

The adapter passes SATA 3 6 Gbps signals while remaining backward compatible with SATA 2 and SATA 1 host controllers. Throughput is therefore capped by the host port generation rather than the adapter itself. It cannot overcome the speed ceiling of an older SATA revision or the inherent limits of the mSATA SSD installed on it.

Replaces Mechanical 2.5 Inch Drives Using Spare

This board lets you swap a slow 2.5 inch hard drive for an mSATA solid-state drive you already own, improving boot and load times. It is not compatible with M.2 NGFF SSDs, so buyers with only M.2 drives cannot use it. The upgrade is worthwhile when a compatible mSATA SSD is available and the notebook has a free 2.5 inch SATA bay.

Helstu kostir

  • Converts mSATA SSD to 2.5 SATA for easy notebook storage upgrade
  • Compact 5cm low-profile PCB fits tight laptop chassis without space conflicts
  • SATA 6Gbps bandwidth preserves original SSD read-write performance
  • Plug-and-play installation requires no drivers or software
  • Reuses spare mSATA drive to replace mechanical HDD and boost responsiveness

Tæknilýsing

Engin birt tæknilýsing fyrir þessa vöru enn.

Spurningar um þessa vöru

Should I choose a different adapter length or form factor for my laptop?

The board is a 5 cm low-profile PCB with no metal 2.5 inch shell, so it fits tight notebook bays where a full-height caddy would not.

Will my mSATA SSD keep its full speed once installed on this adapter?

The adapter passes SATA 3 6 Gbps bandwidth and is backward compatible with SATA 2 and SATA 1, preserving the drive's native read and write performance.

Does the SATA 3 interface limit the drive in any practical way?

The SATA 3 link caps transfer at 6 Gbps, so the SSD cannot exceed that ceiling, but the adapter adds no extra overhead beyond the standard SATA specification.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.