Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Black standalone USB duplicator with LCD screen and seven slots

Systor

Systor SYSUSB30100-7 1-to-7 USB 3.0/3.1 Duplicator

SKU CH-F15Q-3HBC5

Standalone USB duplicator copies one source to seven targets at up to 100 MB/s with LCD control and bit-for-bit verification

  • TypeUSB Flash Drive Duplicator
  • Target1 to 7
  • Buffer Memory256M
  • Supported MediaUSB 1.1, USB 2.0, USB 3.0, USB 3.1
  • Data Transfer Rate100MB/sec
  • Language SupportEnglish or Japanese

Target Size 1 to 07

Näita veel 7 konfiguratsiooni

Läbikriipsutatud versioonid on olemas, kuid neid pole siin saadaval.

DATA TRANSFER RATE USB 3.0/3.1 - 6GB/min [100MB/sec]

  • Standalone operation with no computer required
  • Copy speeds up to 100 MB per second
  • Supports USB 1.1 through USB 3.1 drives
  • Bit-by-bit compare verifies every duplication
  • LCD interface with synchronous and asynchronous modes

Standalone USB 3.0/3.1 Flash Duplicator

The Systor SYSUSB30100-7 is a standalone duplicator that copies one source USB flash drive to up to seven targets without a host computer. It supports USB 1.1, 2.0, 3.0 and 3.1 media and reaches a transfer rate of 100MB/sec. An integrated LCD screen and four-key panel control all operations.

Suited for high-volume USB copying.

This unit suits IT departments, duplication services and OEMs that need rapid, simultaneous cloning of USB flash drives in FAT16, FAT32, NTFS or Linux file systems. It does not support optical discs, hard drives, memory cards or network-attached workflows. Buyers requiring software-driven imaging or non-USB target interfaces should consider a different device.

Seven target ports with asynchronous operation

The defining specification is the 1-to-7 target configuration combined with asynchronous copy mode, allowing each channel to load, unload and copy independently. Buffer memory of 256M and bit-for-bit hardware comparison ensure reliable duplication across all seven slots.

Põhijooned

  • Standalone operation with no computer required
  • Copy speeds up to 100 MB per second
  • Supports USB 1.1 through USB 3.1 drives
  • Bit-by-bit compare verifies every duplication
  • LCD interface with synchronous and asynchronous modes

Tehnilised andmed

BrandSystor
ModelSYSUSB30100-7
TypeUSB Flash Drive Duplicator
Target1 to 7
Buffer Memory256M
Supported MediaUSB 1.1, USB 2.0, USB 3.0, USB 3.1
Data Transfer Rate100MB/sec
Language SupportEnglish or Japanese
DisplayLCD Screen
Operating TypeStandalone
Panel ColorBlack
Load TypeSlot
FeaturesQuick Copy: FAT16/32, NTFS, Linux(EXT2/EXT3/EXT4) Whole Media Copy: All Formats
Environmental SpecOperating Humidity: 15% ~ 90%
Power Supply115V / 230V

Selle mudeli teised versioonid

5 veel samast sarjast

Sama seeria, erinev mälumaht, jahutus või taktsagedus — võrrelge enne otsustamist.

Küsimused selle toote kohta

Does the duplicator need a host PC to copy USB 3.0 or 3.1 drives?

No, it operates completely standalone with its own multi-core processor and LCD interface, so no computer or software is required.

Can I mix USB 2.0 and USB 3.0 flash drives in the same copy job?

Yes, the unit supports USB 1.1, 2.0, 3.0 and 3.1 media simultaneously across its seven target slots.

How do I confirm each copy finished without errors?

The built-in bit-for-bit hardware comparison runs after every duplication and the LCD reports pass or fail for each channel.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.