Akceptujemy kryptowaluty — posiadane środki można więc wykorzystać na zakup prawdziwego sprzętu.Płatność kryptowalutą — realny sprzęt w zamian. Bezpłatna, ubezpieczona dostawa na całym świecie powyżej 399 $. Neutralne kartony, bez oznaczeń, wysyłane z Niemiec.Bezpłatna, ubezpieczona dostawa powyżej 399 $. Kurs zostaje zablokowany na 30 minut od otwarcia kasy.Kurs zablokowany na 30 minut. Każdy produkt jest fabrycznie zapieczętowany, jego numer seryjny jest sprawdzany, a całość objęta jest 24-miesięczną gwarancją.Zapieczętowane fabrycznie, 24 miesiące gwarancji.

Obserwowane produkty Zaloguj się

Systor

Systor SYSUSB30100-7 1-to-7 USB 3.0/3.1 Duplicator

SKU CH-F15Q-3HBC5

Standalone USB duplicator copies one source to seven targets at up to 100 MB/s with LCD control and bit-for-bit verification

  • TypeUSB Flash Drive Duplicator
  • Target1 to 7
  • Buffer Memory256M
  • Supported MediaUSB 1.1, USB 2.0, USB 3.0, USB 3.1
  • Data Transfer Rate100MB/sec
  • Language SupportEnglish or Japanese

Target Size 1 to 07

Pokaż jeszcze 7 konfiguracji

Przekreślone wersje istnieją, ale nie są dostępne w tym miejscu.

DATA TRANSFER RATE USB 3.0/3.1 - 6GB/min [100MB/sec]

  • Standalone operation with no computer required
  • Copy speeds up to 100 MB per second
  • Supports USB 1.1 through USB 3.1 drives
  • Bit-by-bit compare verifies every duplication
  • LCD interface with synchronous and asynchronous modes

Standalone USB 3.0/3.1 Flash Duplicator

The Systor SYSUSB30100-7 is a standalone duplicator that copies one source USB flash drive to up to seven targets without a host computer. It supports USB 1.1, 2.0, 3.0 and 3.1 media and reaches a transfer rate of 100MB/sec. An integrated LCD screen and four-key panel control all operations.

Suited for high-volume USB copying.

This unit suits IT departments, duplication services and OEMs that need rapid, simultaneous cloning of USB flash drives in FAT16, FAT32, NTFS or Linux file systems. It does not support optical discs, hard drives, memory cards or network-attached workflows. Buyers requiring software-driven imaging or non-USB target interfaces should consider a different device.

Seven target ports with asynchronous operation

The defining specification is the 1-to-7 target configuration combined with asynchronous copy mode, allowing each channel to load, unload and copy independently. Buffer memory of 256M and bit-for-bit hardware comparison ensure reliable duplication across all seven slots.

Najważniejsze cechy

  • Standalone operation with no computer required
  • Copy speeds up to 100 MB per second
  • Supports USB 1.1 through USB 3.1 drives
  • Bit-by-bit compare verifies every duplication
  • LCD interface with synchronous and asynchronous modes

Specyfikacja

BrandSystor
ModelSYSUSB30100-7
TypeUSB Flash Drive Duplicator
Target1 to 7
Buffer Memory256M
Supported MediaUSB 1.1, USB 2.0, USB 3.0, USB 3.1
Data Transfer Rate100MB/sec
Language SupportEnglish or Japanese
DisplayLCD Screen
Operating TypeStandalone
Panel ColorBlack
Load TypeSlot
FeaturesQuick Copy: FAT16/32, NTFS, Linux(EXT2/EXT3/EXT4) Whole Media Copy: All Formats
Environmental SpecOperating Humidity: 15% ~ 90%
Power Supply115V / 230V

Inne wersje tego modelu

Jeszcze 5 w tej samej serii

Ta sama rodzina, inna pamięć, inne chłodzenie lub taktowanie — proszę porównać przed decyzją.

Pytania dotyczące tego produktu

Does the duplicator need a host PC to copy USB 3.0 or 3.1 drives?

No, it operates completely standalone with its own multi-core processor and LCD interface, so no computer or software is required.

Can I mix USB 2.0 and USB 3.0 flash drives in the same copy job?

Yes, the unit supports USB 1.1, 2.0, 3.0 and 3.1 media simultaneously across its seven target slots.

How do I confirm each copy finished without errors?

The built-in bit-for-bit hardware comparison runs after every duplication and the LCD reports pass or fail for each channel.

Także w tym dziale

Klienci porównywali też te produkty

Ten sam dział, ta sama kasa — osiem kryptowalut i 30-minutowa blokada kursu.