NEMIX RAM DDR5-5600 2TB (16x128GB) ECC RDIMM CL46 1.1V Supermicro H14SST-G memory upgrade
- 2TB (16 x 128GB)
- 288-Pin DDR5 RDIMM
Prihvaćamo kriptovalute — tako kriptovalute koje posjedujete mogu kupiti pravi hardver.Plaćajte kriptovalutom, trošite je na pravi hardver. Besplatna osigurana dostava diljem svijeta iznad 399 $. Obični vanjski kartoni bez oznaka, otpremaju se iz Njemačke.Besplatna osigurana dostava iznad 399 $. Vaš je tečaj blokiran 30 minuta od otvaranja blagajne.Tečaj blokiran 30 minuta. Svaki je artikl zapečaćen, njegov serijski broj provjeren, i pokriven jamstvom od 24 mjeseca.Zapečaćen, jamstvo 24 mjeseca.
Crucial
A 4GB DDR3 1866 ECC unbuffered DIMM with CL13 latency and 1.50V operation for server memory upgrades
This Crucial CT51272BA186DJ is a 4GB DDR3 1866 ECC unbuffered DIMM built for server platforms that require error-correcting memory. It operates at 1.50V with a CAS latency of CL13 and uses a 240-pin interface. The module is sold new as a single stick ranked 1Rx8.
Replacing older DDR3 1066 or 1333 modules with this 1866 speed part increases memory bandwidth where the platform supports it. The jump is worth it when the motherboard and CPU memory controller are qualified for PC3 14900 operation and the system can utilise ECC protection.
Confirm the motherboard has 240-pin DDR3 DIMM slots and a DDR3-enabled chipset before ordering. DDR3 modules will not fit DDR2 or DDR sockets. Ensure the platform accepts unbuffered ECC DIMMs rather than registered or fully buffered types.
| Brand | Crucial |
|---|---|
| Model | CT51272BA186DJ |
| Capacity | 4GB |
| Type | 240-Pin DDR3 SDRAM |
| Speed | DDR3 1866 (PC3 14900) |
| CAS Latency | CL13 |
| Voltage | 1.50V |
| ECC | Yes |
| Buffered/Registered | Unbuffered |
| Rank | 1Rx8 |
| Multi-channel Kit | Dual Channel Kit |
| Chipset | Major Brand Chipset |
| Heat Spreader | No |
| Težina pošiljke | 0.07 kg |
| Dimenzije pakiranja | 155 × 122 × 13 mm |
The module uses the standard 240-pin DDR3 form factor and requires a motherboard with DDR3-enabled chipset and matching DIMM slots; it will not fit DDR2 or DDR sockets.
Align the notch on the gold edge connector with the key in the slot, press straight down until both side clips click, and verify the system reports 4 GB at 1866 MT/s with ECC active.
Replace it if memory diagnostics report correctable ECC errors that increase over time, if the server fails to POST with the kit installed, or when you upgrade to a platform that no longer supports DDR3.
Također u ovoj kategoriji
Ista polica, ista blagajna — osam valuta i blokada tečaja na 30 minuta.
Ono što šaljete, i ono u čemu gledate cijene.
Poslano iz Vašeg novčanika na blagajni
Samo prikaz — katalog je izražen u dolarima
Nijedna valuta ne odgovara.
Odaberite jezik na kojem Vam se stranica obraća.
Novi ste ovdje?
Već imate račun?
Ne postoji automatsko resetiranje: ova trgovina ne šalje e-poštu, stoga ne postoji jednokratna poveznica koju biste mogli zatražiti. Ostavite adresu uz svoj račun, netko će je ručno obraditi.
Zahtjev zaprimljen
Ništa neće stići u Vaš pretinac e-pošte — ova trgovina uopće ne šalje e-poštu. Netko će to ručno preuzeti.
Sjetili ste se?