Prihvaćamo kriptovalute — tako kriptovalute koje posjedujete mogu kupiti pravi hardver.Plaćajte kriptovalutom, trošite je na pravi hardver. Besplatna osigurana dostava diljem svijeta iznad 399 $. Obični vanjski kartoni bez oznaka, otpremaju se iz Njemačke.Besplatna osigurana dostava iznad 399 $. Vaš je tečaj blokiran 30 minuta od otvaranja blagajne.Tečaj blokiran 30 minuta. Svaki je artikl zapečaćen, njegov serijski broj provjeren, i pokriven jamstvom od 24 mjeseca.Zapečaćen, jamstvo 24 mjeseca.

Praćeni artikli Prijava
Green circuit board with black memory chips and gold edge connector

OWC

OWC 4GB DDR4 2133MHz CL15 1.2V 288pin UDIMM memory upgrade

SKU CH-AZ4J-4QX7B

A 4GB DDR4 2133MHz CL15 UDIMM upgrade for HP Envy Phoenix 860-036ng, 860-041ng, 860-050nc, 860-070na and 860-080no desktops

  • Capacity4GB
  • Type288-Pin DDR4 Non-ECC UDIMM
  • SpeedDDR4 2133 (PC4 17000)
  • CAS LatencyCL15
  • Voltage1.2V
  • ECCNo
  • Boosts PC responsiveness with a 4 GB DDR4 2133 MHz CL15 module
  • Low 1.2 V operation cuts power draw and heat
  • JEDEC and RoHS compliant for a warranty-safe upgrade
  • 288-pin unbuffered UDIMM fits HP Envy Phoenix 860-036ng 860-041ng 860-050nc 860-070na 860-080no
  • Simple DIY install lets you add memory in minutes

Compatible DDR4 upgrade for HP Envy Phoenix

This 4 GB DDR4 UDIMM runs at 2133 MHz with CL15 latency and 1.2 V operation. It is built to JEDEC specifications and tested for the HP Envy Phoenix 860-036ng, 860-041ng, 860-050nc, 860-070na and 860-080no desktops. The unbuffered, non-ECC module uses a 288-pin form factor.

Suits owners of the listed Phoenix models adding

Buyers with other HP desktops or custom builds should verify DDR4 2133 support before purchasing. Systems requiring ECC, registered memory or speeds above PC4-17000 will not be served by this module. It is a single 4 GB stick, so configurations needing matched pairs or larger single modules must look elsewhere.

No accessories or software are included

The upgrade consists solely of the memory module. Installation relies on the system owner following standard DIMM insertion steps. Any performance gain comes from the added capacity and JEDEC-compliant timing, not from bundled utilities or heat spreaders.

Istaknuto

  • Boosts PC responsiveness with a 4 GB DDR4 2133 MHz CL15 module
  • Low 1.2 V operation cuts power draw and heat
  • JEDEC and RoHS compliant for a warranty-safe upgrade
  • 288-pin unbuffered UDIMM fits HP Envy Phoenix 860-036ng 860-041ng 860-050nc 860-070na 860-080no
  • Simple DIY install lets you add memory in minutes

Specifikacije

BrandOWC
Part Number2U1D41R804GB
Capacity4GB
Type288-Pin DDR4 Non-ECC UDIMM
SpeedDDR4 2133 (PC4 17000)
CAS LatencyCL15
Voltage1.2V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
Heat SpreaderNo
Compatible SystemHP ENVY Phoenix 860-036ng
HP ENVY Phoenix 860-041ng
HP ENVY Phoenix 860-050nc
HP ENVY Phoenix 860-070na
HP ENVY Phoenix 860-080no

Druge verzije ovog modela

još 5 u istoj seriji

Ista obitelj, različita memorija, hladnjak ili frekvencija — usporedite prije kupnje.

Pitanja o ovom artiklu

Does the HP Envy Phoenix 860-036ng motherboard have a free 288-pin DDR4 slot for this 4 GB module?

The module fits any standard DDR4 UDIMM slot on the HP Envy Phoenix 860-036ng, 860-041ng, 860-050nc, 860-070na or 860-080no; check that at least one slot is empty before installing.

Will this DDR4 2133 CL15 1.2 V stick run with the existing memory in my HP Envy Phoenix 860-070na?

It is JEDEC-standard DDR4 2133 CL15 1.2 V, so it will operate alongside the factory memory at the system's default speed and voltage.

How can I verify the new 4 GB DDR4 2133 CL15 module is recognised after installation?

Power on the HP Envy Phoenix and confirm the total memory in BIOS or Windows Task Manager shows the extra 4 GB running at 2133 MHz.

Također u ovoj kategoriji

Kupci su usporedili ovo

Ista polica, ista blagajna — osam valuta i blokada tečaja na 30 minuta.