Prihvaćamo kriptovalute — tako kriptovalute koje posjedujete mogu kupiti pravi hardver.Plaćajte kriptovalutom, trošite je na pravi hardver. Besplatna osigurana dostava diljem svijeta iznad 399 $. Obični vanjski kartoni bez oznaka, otpremaju se iz Njemačke.Besplatna osigurana dostava iznad 399 $. Vaš je tečaj blokiran 30 minuta od otvaranja blagajne.Tečaj blokiran 30 minuta. Svaki je artikl zapečaćen, njegov serijski broj provjeren, i pokriven jamstvom od 24 mjeseca.Zapečaćen, jamstvo 24 mjeseca.

Praćeni artikli Prijava
Green circuit board with black memory chips and gold edge connector

OWC

OWC 8GB DDR3 1600 CL11 2Rx8 240-pin 1.5V UDIMM for OptiPlex 9010

SKU CH-1T7J-Q4FD6

8GB DDR3 1600 CL11 UDIMM upgrade for OptiPlex 9010 desktop, SFF and tower models

  • Capacity8GB
  • Type240-Pin DDR3 Non-ECC UDIMM
  • SpeedDDR3 1600 (PC3 12800)
  • CAS LatencyCL11
  • Voltage1.5V
  • ECCNo
  • Boost responsiveness with 8 GB DDR3 1600 CL11 memory
  • JEDEC-standard 1.5 V module ensures warranty-safe upgrade
  • Unbuffered 2Rx8 design fits OptiPlex 9010 Desktop, SFF and Tower
  • 240-pin DIMM installs easily for immediate multitasking gains
  • PC3-12800 speed rating supports faster data throughput

8GB DDR3 upgrade for OptiPlex 9010

This 8GB DDR3 1600 CL11 module is built for Dell OptiPlex 9010 Desktop, SFF and Tower systems. It uses a 240-pin UDIMM form factor and runs at 1.5V without ECC or registered buffering. The single 2Rx8 rank adds capacity for everyday workloads on these specific platforms.

Check motherboard slots and memory limits

Verify the OptiPlex 9010 has a free 240-pin DDR3 slot before ordering. Confirm the system BIOS recognises 8GB non-ECC unbuffered modules and that total installed memory will not exceed the board's maximum supported capacity. Matching existing modules by speed and voltage avoids stability issues.

JEDEC compliance and lifetime support

The module meets JEDEC and RoHS standards for a warranty-safe upgrade. OWC provides a limited lifetime warranty with free technical support and an advanced replacement programme. No heat spreader is included, so airflow in the chassis should be adequate for sustained operation.

Istaknuto

  • Boost responsiveness with 8 GB DDR3 1600 CL11 memory
  • JEDEC-standard 1.5 V module ensures warranty-safe upgrade
  • Unbuffered 2Rx8 design fits OptiPlex 9010 Desktop, SFF and Tower
  • 240-pin DIMM installs easily for immediate multitasking gains
  • PC3-12800 speed rating supports faster data throughput

Specifikacije

BrandOWC
Part Number1U6D32R808GB
Capacity8GB
Type240-Pin DDR3 Non-ECC UDIMM
SpeedDDR3 1600 (PC3 12800)
CAS LatencyCL11
Voltage1.5V
ECCNo
Buffered/RegisteredUnbuffered
Rank2Rx8
Heat SpreaderNo
Compatible SystemDell OptiPlex 9010 Desktop
Dell OptiPlex 9010 SFF
Dell OptiPlex 9010 Tower

Druge verzije ovog modela

još 5 u istoj seriji

Ista obitelj, različita memorija, hladnjak ili frekvencija — usporedite prije kupnje.

Pitanja o ovom artiklu

Does the 8GB DDR3 1600 module arrive as a single stick or do I need to buy anything else to install it?

The upgrade consists of one 8GB DDR3 1600 CL11 2Rx8 240-pin 1.5V Non-ECC UDIMM. No extra parts are required for installation.

The title lists OptiPlex 9010 Desktop, SFF and Tower — which version should I choose for my 9010 Tower?

The same 8GB DDR3 1600 PC3-12800 CL11 2Rx8 240-pin 1.5V Non-ECC UDIMM fits all three OptiPlex 9010 form factors, including the Tower.

What does the 1600MHz CL11 rating actually deliver once the module is seated in an OptiPlex 9010?

The module runs at DDR3 1600 (PC3-12800) with CL11 latency at 1.5V, providing a JEDEC-standard speed increase for the OptiPlex 9010 platform.

Također u ovoj kategoriji

Kupci su usporedili ovo

Ista polica, ista blagajna — osam valuta i blokada tečaja na 30 minuta.