Prihvaćamo kriptovalute — tako kriptovalute koje posjedujete mogu kupiti pravi hardver.Plaćajte kriptovalutom, trošite je na pravi hardver. Besplatna osigurana dostava diljem svijeta iznad 399 $. Obični vanjski kartoni bez oznaka, otpremaju se iz Njemačke.Besplatna osigurana dostava iznad 399 $. Vaš je tečaj blokiran 30 minuta od otvaranja blagajne.Tečaj blokiran 30 minuta. Svaki je artikl zapečaćen, njegov serijski broj provjeren, i pokriven jamstvom od 24 mjeseca.Zapečaćen, jamstvo 24 mjeseca.

Praćeni artikli Prijava
Enclosed dual-laser engraver with built-in camera, light finish

XTOOL

XTOOL F2 15W Diode 5W IR Dual Laser Engraver

SKU CH-GWGH-Q6HCJ

Dual 15W diode and 5W IR lasers engrave 300+ materials at up to 6000 mm/s with a 50MP camera for 0.1 mm alignment

  • Dual 15W diode and 5W IR lasers process 300+ materials
  • 50MP camera gives 0.1 mm alignment accuracy on small pieces
  • 6000 mm/s speed finishes a card engraving in 3 seconds
  • Fully enclosed leak-proof design with built-in fan removes fumes for indoor use
  • Arrives fully assembled with material presets and optional RA3 Slide Extension accessories

Dual-laser versatility for makers

The XTOOL F2 combines a 15W diode laser with a 5W IR laser in a single portable engraver. This dual-source design enables work on over 300 materials, from metals that respond to infrared to woods and acrylics suited to diode cutting. It arrives fully assembled with built-in material presets, so users can start projects without complex setup or guesswork.

Sustained speed and precision

The engraver reaches speeds up to 6000mm/s, completing a card engraving in about three seconds. A 50MP camera visualises the entire workspace and provides up to 0.1 mm alignment accuracy on small pieces. Motion accuracy of .00199 inches ensures consistent detail during long runs, while optional accessories such as the RA3 and Slide Extension support efficient batch processing.

Enclosed safety and fume management

A fully enclosed, leak-proof chassis allows safe operation in workshops or retail spaces. An integrated fan works with an optional purifier to remove fumes for clean indoor use. The sealed design contains stray light and debris, maintaining a tidy environment during extended engraving or cutting sessions.

Istaknuto

  • Dual 15W diode and 5W IR lasers process 300+ materials
  • 50MP camera gives 0.1 mm alignment accuracy on small pieces
  • 6000 mm/s speed finishes a card engraving in 3 seconds
  • Fully enclosed leak-proof design with built-in fan removes fumes for indoor use
  • Arrives fully assembled with material presets and optional RA3 Slide Extension accessories

Specifikacije

Za ovaj artikl još nisu objavljene specifikacije.

Pitanja o ovom artiklu

How loud is the built-in fan when the F2 runs all day?

The machine uses a fully enclosed, leak-proof design with an integrated fan that removes fumes for clean indoor use.

What must I already own to start engraving with the 15 W diode and 5 W IR lasers?

The unit arrives fully assembled with built-in material presets and a 50 MP camera for alignment, so no extra hardware is required to begin.

Can I add the RA3 rotary and Slide Extension to my existing workshop setup later?

Yes, the F2 supports accessories such as the RA3 and Slide Extension for diverse projects and efficient batch processing.

Također u ovoj kategoriji

Kupci su usporedili ovo

Ista polica, ista blagajna — osam valuta i blokada tečaja na 30 minuta.