Elfogadjuk a kriptovalutát — így az Ön birtokában lévő érmékből valódi hardvert vásárolhat.Fizessen kriptóval, és költse el valódi hardverre. 399 $ felett világszerte díjmentes a biztosított szállítás. Egyszerű, jelöletlen külső kartonok, Németországból küldve.399 $ felett díjmentes a biztosított szállítás. Az Ön árfolyama a pénztár megnyitásától számított 30 percre zárolva marad.Árfolyam zárolva 30 percre. Minden termék gyárilag zárt, sorozatszáma ellenőrzött, és 24 hónapos garancia fedezi.Zárt csomagolás, 24 hónap garancia.

Árfigyelő lista Bejelentkezés
Green 240-pin DDR3 DIMM module with black chips, no heat spreader

A-Tech

A-Tech 4GB DDR3 1600MHz CL11 1.5V HP 655410-D88 717046-001 688600-001 2Rx8 Desktop RAM

SKU CH-4AED-D0JS2

A 4 GB DDR3 DIMM running at 1600 MHz with CL11 latency and 1.5 V for HP desktops using part numbers 655410-D88, 717046-001 or 688600-001

  • Capacity4GB
  • SpeedDDR3 1600 (PC3 12800)
  • Tested Frequency1600
  • CAS LatencyCL11
  • Voltage1.50V
  • ECCNo
  • Boosts multitasking with 4GB DDR3 1600MHz CL11
  • Runs at standard 1.5V DDR3 voltage for stability
  • 240-pin DIMM fits compatible HP desktop slots
  • Non-ECC unbuffered design for standard desktop use
  • Replaces HP part numbers 655410-D88 717046-001 688600-001

HP-Compatible 4GB DDR3 Module

This 4GB DDR3 module is a direct replacement for HP part numbers 655410-D88, 717046-001 and 688600-001. It operates at 1600MHz with a CL11 latency and standard 1.5V voltage. The unbuffered, non-ECC DIMM uses a 240-pin interface and a 2Rx8 chip organisation. It is built for desktop systems that require these exact HP specifications.

Suitable for HP Desktop Upgrades

This module suits owners of compatible HP desktops needing a 4GB DDR3 upgrade to match the original factory specification. Systems that require ECC memory, registered DIMMs, a different voltage, or a higher density per slot should look at alternative modules. Compatibility depends on the motherboard accepting 2Rx8 unbuffered DDR3 at 1.5V.

2Rx8 Organisation Decides Fit

The 2Rx8 chip organisation is the critical specification that determines whether this module will work in a given HP desktop. Some HP platforms only accept 1Rx8 or 1Rx16 configurations and will not post with a 2Rx8 stick. Verify the original module label or the system service manual for the rank and organisation details before purchasing.

Erősségek

  • Boosts multitasking with 4GB DDR3 1600MHz CL11
  • Runs at standard 1.5V DDR3 voltage for stability
  • 240-pin DIMM fits compatible HP desktop slots
  • Non-ECC unbuffered design for standard desktop use
  • Replaces HP part numbers 655410-D88 717046-001 688600-001

Műszaki adatok

BrandA-Tech
SeriesCompatible Replacement for HP
Model655410-D88, 717046-001, 688600-001
Capacity4GB
SpeedDDR3 1600 (PC3 12800)
Tested Frequency1600
CAS LatencyCL11
Voltage1.50V
ECCNo
Buffered/RegisteredUnbuffered
ChipsetMajor Brand Chipset
Heat SpreaderNo
Features655410-D88, 717046-001, 688600-001
Recommend UseCompatible Replacement for HP 655410-D88, 717046-001, 688600-001

Kérdések a termékről

What does the DDR3 1600 PC3-12800 rating mean for real-world throughput?

The module runs at 1600 MHz with a peak transfer rate of 12800 MB/s; actual bandwidth depends on the motherboard's memory controller and whether it operates in single- or dual-channel mode.

Will this 240-pin DIMM fit the memory slots on my HP desktop?

The stick uses the standard 240-pin DDR3 DIMM form factor, so it fits any desktop board that accepts unbuffered non-ECC DDR3 DIMMs; verify your model's maximum capacity per slot before installing.

How do I install the module and what is the common mistake to avoid?

Power off the PC, open the case, align the notch on the 240-pin edge connector with the slot key, press firmly until both retention clips click, then power on; the frequent error is stopping before the clips latch, leaving the module partially seated.

Szintén ezen a polcon

Vásárlók ezeket hasonlították össze

Ugyanaz a polc, ugyanaz a pénztár — nyolc pénznem és 30 perces árfolyamzár.