Elfogadjuk a kriptovalutát — így az Ön birtokában lévő érmékből valódi hardvert vásárolhat.Fizessen kriptóval, és költse el valódi hardverre. 399 $ felett világszerte díjmentes a biztosított szállítás. Egyszerű, jelöletlen külső kartonok, Németországból küldve.399 $ felett díjmentes a biztosított szállítás. Az Ön árfolyama a pénztár megnyitásától számított 30 percre zárolva marad.Árfolyam zárolva 30 percre. Minden termék gyárilag zárt, sorozatszáma ellenőrzött, és 24 hónapos garancia fedezi.Zárt csomagolás, 24 hónap garancia.

Árfigyelő lista Bejelentkezés
LORDWORLD LX-224 serial bus servo with bracket, metal finish

LORDWORLD

LORDWORLD LX-224 Serial Bus Servo 20KG 240 Degree with Bracket

SKU CH-BHCF-T660K

Serial bus servo delivers 20 kg torque across 240 degrees with dual ball bearings and a debug system for position, temperature and voltage monitoring

  • 20KG torque powers heavy robot joints
  • 240 degree range enables wide motion arcs
  • Serial bus connectors link multiple servos in series
  • Debug system shows position temperature voltage live
  • Dual ball bearings reduce friction for smooth operation

Servo for Robot Joints and DIY Builds

The LORDWORLD LX-224 serial bus servo delivers 20KG of torque through a full metal gear train supported by dual ball bearings. A high-precision potentiometer provides angle feedback across a 240 degree range. The integrated debug system reports position, temperature and voltage data during development. Three connectors allow daisy-chaining multiple units on a single bus for articulated projects.

Suited for Multi-Axis Arms and Legged Platforms

Makers building robot arms, hexapods or humanoid prototypes benefit from the serial bus topology and the ability to switch between servo mode and gear motor mode. The bracket is included for direct mounting. Builders who require continuous rotation without position limits or a wider angular range than 240 degrees should consider alternative actuator types.

20KG Torque Rating Decides Fit

The 20KG torque figure is the primary specification that determines whether this servo can move your intended load at the required speed. Verify the stall torque against your mechanical advantage calculations before committing to the design. The 240 degree travel and serial bus interface are fixed constraints that define the motion envelope and wiring architecture.

Erősségek

  • 20KG torque powers heavy robot joints
  • 240 degree range enables wide motion arcs
  • Serial bus connectors link multiple servos in series
  • Debug system shows position temperature voltage live
  • Dual ball bearings reduce friction for smooth operation

Műszaki adatok

BrandLORDWORLD

Kérdések a termékről

How do I chain the LX-224 servos together using the LewanSoul serial bus connectors?

Plug each servo into the next using the three-pin serial bus connectors so the signal passes through the chain; the step often missed is ensuring every connector is fully seated and the bus termination is correct for the controller.

Which parts of the LX-224 will wear first and need replacement after heavy use?

The dual ball bearings and the internal high-precision potentiometer are the components that degrade with continuous load; the all-metal gear train lasts longer but should be inspected for backlash.

At what point does the LX-224 hit its thermal or torque limit during sustained operation?

The 20KG torque rating is the first hard limit; if the load approaches that value the debug system will report rising temperature and voltage drop, signalling the servo is at its continuous-duty ceiling.

Szintén ezen a polcon

Vásárlók ezeket hasonlították össze

Ugyanaz a polc, ugyanaz a pénztár — nyolc pénznem és 30 perces árfolyamzár.