Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
LORDWORLD LX-224 serial bus servo with bracket, metal finish

LORDWORLD

LORDWORLD LX-224 Serial Bus Servo 20KG 240 Degree with Bracket

SKU CH-BHCF-T660K

Serial bus servo delivers 20 kg torque across 240 degrees with dual ball bearings and a debug system for position, temperature and voltage monitoring

  • 20KG torque powers heavy robot joints
  • 240 degree range enables wide motion arcs
  • Serial bus connectors link multiple servos in series
  • Debug system shows position temperature voltage live
  • Dual ball bearings reduce friction for smooth operation

Servo for Robot Joints and DIY Builds

The LORDWORLD LX-224 serial bus servo delivers 20KG of torque through a full metal gear train supported by dual ball bearings. A high-precision potentiometer provides angle feedback across a 240 degree range. The integrated debug system reports position, temperature and voltage data during development. Three connectors allow daisy-chaining multiple units on a single bus for articulated projects.

Suited for Multi-Axis Arms and Legged Platforms

Makers building robot arms, hexapods or humanoid prototypes benefit from the serial bus topology and the ability to switch between servo mode and gear motor mode. The bracket is included for direct mounting. Builders who require continuous rotation without position limits or a wider angular range than 240 degrees should consider alternative actuator types.

20KG Torque Rating Decides Fit

The 20KG torque figure is the primary specification that determines whether this servo can move your intended load at the required speed. Verify the stall torque against your mechanical advantage calculations before committing to the design. The 240 degree travel and serial bus interface are fixed constraints that define the motion envelope and wiring architecture.

Helstu kostir

  • 20KG torque powers heavy robot joints
  • 240 degree range enables wide motion arcs
  • Serial bus connectors link multiple servos in series
  • Debug system shows position temperature voltage live
  • Dual ball bearings reduce friction for smooth operation

Tæknilýsing

BrandLORDWORLD

Spurningar um þessa vöru

How do I chain the LX-224 servos together using the LewanSoul serial bus connectors?

Plug each servo into the next using the three-pin serial bus connectors so the signal passes through the chain; the step often missed is ensuring every connector is fully seated and the bus termination is correct for the controller.

Which parts of the LX-224 will wear first and need replacement after heavy use?

The dual ball bearings and the internal high-precision potentiometer are the components that degrade with continuous load; the all-metal gear train lasts longer but should be inspected for backlash.

At what point does the LX-224 hit its thermal or torque limit during sustained operation?

The 20KG torque rating is the first hard limit; if the load approaches that value the debug system will report rising temperature and voltage drop, signalling the servo is at its continuous-duty ceiling.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.