PrimoChill Male to Female G1/4 30 Degree Rotary Elbow Fitting Razor Red diy cooling
- Fittings
Elfogadjuk a kriptovalutát — így az Ön birtokában lévő érmékből valódi hardvert vásárolhat.Fizessen kriptóval, és költse el valódi hardverre. 399 $ felett világszerte díjmentes a biztosított szállítás. Egyszerű, jelöletlen külső kartonok, Németországból küldve.399 $ felett díjmentes a biztosított szállítás. Az Ön árfolyama a pénztár megnyitásától számított 30 percre zárolva marad.Árfolyam zárolva 30 percre. Minden termék gyárilag zárt, sorozatszáma ellenőrzött, és 24 hónapos garancia fedezi.Zárt csomagolás, 24 hónap garancia.
PrimoChill
A G1/4 rotary elbow that redirects tubing 30 degrees from the mount for tight custom-loop builds
Option UV Orange
Az áthúzott konfigurációk léteznek, de nem érhetők el itt.
The PrimoChill rotary elbow lets custom-loop builders redirect tubing runs by 30 degrees without stressing rigid or flexible lines. A male G 1/4 thread screws into a component or block while the female G 1/4 side accepts any standard fitting. The brass body is coated for corrosion resistance and the UV orange finish reacts under black light for visual impact.
As a passive adapter the fitting adds no heat, noise or electrical draw to the system. Brass conducts heat away from the joint slightly better than plastic alternatives, but the effect on coolant temperature is negligible. The coated surface resists coolant staining so flow remains clean during normal operation.
Under continuous circulation the rotary joint maintains its seal at the rated 30 degree offset without loosening. Brass threads resist galling during repeated re-orientation, and the coating protects against long-term coolant exposure. The fitting imposes no flow restriction beyond the inherent elbow geometry.
| Type | Fittings |
|---|
A modell további verziói
Ugyanaz a termékcsalád, eltérő memória, hűtés vagy órajel — hasonlítsa össze, mielőtt dönt.
Thread the male G1/4 end into the component port by hand, then tighten gently with a wrench on the brass flats. The step many miss is rotating the female end to the exact 30-degree offset you need before locking it down with the compression fitting.
Inspect the O-rings inside both G1/4 threads once a year; replace them if they feel brittle or show flattening. Flush the loop annually to prevent sediment from binding the 30-degree rotary joint, and reapply a thin film of silicone grease on the threads during reassembly.
The 30-degree directional bend creates the primary restriction; its fixed angle and internal radius limit flow rate before the G1/4 threads or the coated brass body reach their pressure ceiling.
Szintén ezen a polcon
Ugyanaz a polc, ugyanaz a pénztár — nyolc pénznem és 30 perces árfolyamzár.
Amivel fizet, és amiben az árakat olvassa.
A pénztárnál küldi el a tárcájából
Csak tájékoztató jellegű — a katalógus dollárban van árazva
Nincs ilyen pénznem.
Válassza ki, milyen nyelven szóljon Önhöz az oldal.
Nincs egyező nyelv.
Először jár itt?
Már van fiókja?
Nincs automatikus visszaállítás: ez a bolt nem küld e-mailt, tehát nincs kérhető egyszer használatos link. Hagyja meg a fiókhoz tartozó címet, azt valaki kézzel átnézi.
Kérés rögzítve
Semmi nem érkezik a postafiókjába — ez a bolt egyáltalán nem küld e-mailt. Ezeket valaki kézzel intézi.
Eszébe jutott?