Prijímame kryptomeny — takže mince, ktoré držíte, môžete zameniť za skutočný hardvér.Plaťte v krypte, miňte ho na skutočný hardvér. Poistená doprava zadarmo po celom svete nad 399 $. Neutrálne kartóny bez potlače, odosielané z Nemecka.Poistená doprava zadarmo nad 399 $. Váš kurz je zablokovaný na 30 minút hneď po otvorení pokladne.Kurz zablokovaný na 30 minút. Každý produkt je zapečatený, jeho sériové číslo je overené a vzťahuje sa naň 24-mesačná záruka.Zapečatené, 24-mesačná záruka.

Sledované položky Prihlásiť sa
UV orange coated brass rotary elbow fitting with male and female G1/4 threads, 30 degree angle

PrimoChill

PrimoChill Male to Female G1/4 30 Degree Rotary Elbow Fitting UV Orange diy cooling

SKU CH-58BF-JKN4K

A G1/4 rotary elbow that redirects tubing 30 degrees from the mount for tight custom-loop builds

  • TypeFittings

Option UV Orange

Zobraziť ďalších 10 konfigurácií

Preškrtnuté verzie existujú, ale nie sú tu skladom.

  • Rotary design lets you aim connections 30 degrees from the mount
  • Male G1/4 to Female G1/4 threads fit standard water-cooling loops
  • Coated brass construction resists corrosion in liquid-cooling systems
  • UV orange finish adds visible accent under UV lighting
  • Redirects tubing runs away from components at unconventional angles

Quick loop re-routing

The PrimoChill rotary elbow lets custom-loop builders redirect tubing runs by 30 degrees without stressing rigid or flexible lines. A male G 1/4 thread screws into a component or block while the female G 1/4 side accepts any standard fitting. The brass body is coated for corrosion resistance and the UV orange finish reacts under black light for visual impact.

Thermals and power in daily use

As a passive adapter the fitting adds no heat, noise or electrical draw to the system. Brass conducts heat away from the joint slightly better than plastic alternatives, but the effect on coolant temperature is negligible. The coated surface resists coolant staining so flow remains clean during normal operation.

Sustained-load behaviour

Under continuous circulation the rotary joint maintains its seal at the rated 30 degree offset without loosening. Brass threads resist galling during repeated re-orientation, and the coating protects against long-term coolant exposure. The fitting imposes no flow restriction beyond the inherent elbow geometry.

Prednosti

  • Rotary design lets you aim connections 30 degrees from the mount
  • Male G1/4 to Female G1/4 threads fit standard water-cooling loops
  • Coated brass construction resists corrosion in liquid-cooling systems
  • UV orange finish adds visible accent under UV lighting
  • Redirects tubing runs away from components at unconventional angles

Špecifikácie

TypeFittings

Ďalšie verzie tohto modelu

Ďalších 5 v tomto rade

Rovnaký rad, iná pamäť, chladič alebo frekvencia — porovnajte pred rozhodnutím.

Otázky k tomuto produktu

How do I install the PrimoChill G1/4 30 degree rotary elbow and which step do people often miss?

Thread the male G1/4 end into the component port by hand, then tighten gently with a wrench on the brass flats. The step many miss is rotating the female end to the exact 30-degree offset you need before locking it down with the compression fitting.

What maintenance or replacement will this coated brass rotary fitting need over time?

Inspect the O-rings inside both G1/4 threads once a year; replace them if they feel brittle or show flattening. Flush the loop annually to prevent sediment from binding the 30-degree rotary joint, and reapply a thin film of silicone grease on the threads during reassembly.

What is the first limit that appears when this 30-degree elbow runs under sustained flow and pressure?

The 30-degree directional bend creates the primary restriction; its fixed angle and internal radius limit flow rate before the G1/4 threads or the coated brass body reach their pressure ceiling.

Aj v tomto oddelení

Zákazníci tiež porovnávali

Rovnaké oddelenie, rovnaká pokladňa — osem mien a kurz zablokovaný na 30 minút.