Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Silver NEMA17 geared stepper motor with detachable wires and flatted shaft

3D Maker World

3D Maker World Kysan 1040222 Geared NEMA17 Stepper Motor 5.2:1 3d printers accessory

SKU CH-ESX2-45YYK

A NEMA17 geared stepper motor with a 5.2:1 ratio delivering 88 N-cm torque for extruder drives, featuring a compact design and 1830 mm detachable wires for easy management

  • High torque of 9 Kg-cm drives demanding extruders
  • 2:1 gear ratio multiplies motor force for heavy loads
  • Detachable 1830 mm wires simplify cable routing
  • Compact NEMA17 body fits tight printer frames
  • 8 mm flatted shaft secures couplers without slipping

Kysan 1040222 Geared NEMA17 Stepper Motor

This NEMA17 geared stepper motor provides massive torque of 9 Kg-cm (88 N-cm, 125 Oz/in) to drive your extruder. A 5.2:1 gear ratio multiplies holding force while keeping the body compact for tight printer frames. The detachable 1,830 mm wire harness simplifies cable routing and maintenance.

Suited For Direct-Drive Extruder Upgrades

Makers converting a Bowden printer to direct drive or replacing a worn stock motor gain the torque needed for consistent filament grip. Builders who need a standard NEMA17 shaft without a gearbox, or who require a different gear ratio for speed-critical axes, should look at other motor types.

5.2:1 Gear Ratio With 8 mm Flatted Shaft

The 5.2:1 reduction delivers 9 Kg-cm output torque from a 2.6 V, 1 A two-phase winding. An 8 mm flatted shaft mates with common extruder gears and couplers, while 2.6 Ω phase resistance and 3.2 mH inductance match typical 3D printer driver settings.

Helstu kostir

  • High torque of 9 Kg-cm drives demanding extruders
  • 2:1 gear ratio multiplies motor force for heavy loads
  • Detachable 1830 mm wires simplify cable routing
  • Compact NEMA17 body fits tight printer frames
  • 8 mm flatted shaft secures couplers without slipping

Tæknilýsing

Engin birt tæknilýsing fyrir þessa vöru enn.

Spurningar um þessa vöru

Will the 8 mm flatted shaft need periodic replacement?

The 8 mm flatted shaft is integral to the Kysan 1040222 motor body and is not a consumable part; only the detachable 1 830 mm wire harness might be swapped if damaged.

What limits continuous operation of the 5.2:1 geared NEMA17 stepper?

With 1 A per phase at 2.6 V and 2.6 Ω resistance, winding heat is the first limit during sustained use; the 100 MΩ insulation rating at 500 VDC defines the thermal ceiling.

How much heat and noise does the 9 Kg-cm geared motor produce all day?

The 5.2:1 gearbox multiplies torque to 9 Kg-cm while reducing output speed, so the motor runs cooler and quieter than a direct-drive NEMA17 at equivalent load.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.