Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Green 240-pin DDR3 UDIMM module with black chips and gold contacts

A-Tech

A-Tech 4GB DDR3 1333 ECC UDIMM 2Rx8 HP 500210-071 500210-571 server RAM

SKU CH-QB9A-9E8EH

4GB DDR3 1333 ECC unbuffered DIMM for HP 500210-071 and 500210-571 servers

  • Capacity4GB
  • SpeedDDR3 1333 (PC3 10600)
  • CAS LatencyCL9
  • Voltage1.50V
  • ECCYes
  • Buffered/RegisteredUnbuffered
  • 4GB capacity expands server memory headroom for heavier workloads
  • DDR3 1333 MHz speed matches PC3-10600 system bus timing
  • ECC UDIMM design detects and corrects single-bit data errors
  • 240-pin unbuffered form factor fits standard DDR3 DIMM slots
  • Replaces HP part numbers 500210-071 and 500210-571

4GB DDR3 1333 ECC UDIMM for HP Servers

This 4GB DDR3 1333 (PC3-10600) module is an unbuffered ECC UDIMM built with a 2Rx8 organisation. It runs at the standard 1.5V and carries a CL9 latency rating. The 240-pin DIMM is designed as a direct replacement for HP part numbers 500210-071 and 500210-571 in compatible server and workstation platforms.

Sustained load behaviour with ECC protection

Error-correcting code detects and corrects single-bit errors during continuous operation, helping to prevent data corruption under heavy, long-running workloads. Unbuffered architecture keeps latency low for each access while the 2Rx8 rank layout allows the memory controller to interleave across ranks. The 1.5V supply remains within standard DDR3 limits, so thermal output stays consistent during extended use.

Verify platform support before ordering

Confirm that your system accepts DDR3 1333 ECC UDIMM modules in a 240-pin slot and that the firmware enables ECC on unbuffered DIMMs. Check the maximum supported capacity per slot and the total number of populated channels allowed by the memory controller. Ensure the motherboard or server board is qualified for 2Rx8 rank configurations at this speed and voltage.

Helstu kostir

  • 4GB capacity expands server memory headroom for heavier workloads
  • DDR3 1333 MHz speed matches PC3-10600 system bus timing
  • ECC UDIMM design detects and corrects single-bit data errors
  • 240-pin unbuffered form factor fits standard DDR3 DIMM slots
  • Replaces HP part numbers 500210-071 and 500210-571

Tæknilýsing

BrandA-Tech
Capacity4GB
SpeedDDR3 1333 (PC3 10600)
CAS LatencyCL9
Voltage1.50V
ECCYes
Buffered/RegisteredUnbuffered
Rank2Rx8
ChipsetMajor Brand Chipset
FeaturesMajor Brand Chips

Spurningar um þessa vöru

Does this 1.50 V DDR3 1333 module draw much power or generate extra heat when the server runs all day?

It operates at standard 1.50 V DDR3 voltage, so power draw and heat output are typical for a 4 GB DDR3 1333 ECC UDIMM under continuous load.

What must the motherboard provide for this 240-pin DDR3 ECC UDIMM to work?

A DDR3 DIMM slot that accepts unbuffered ECC modules at 1.5 V and supports 2Rx8 organisation.

Will this DDR3 1333 CL9 stick work in a system that currently runs slower DDR3 modules?

The module runs at DDR3 1333 (PC3-10600) CL9; the motherboard will set the common speed for all installed DIMMs.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.