NEMIX RAM DDR5-5600 2TB (16x128GB) ECC RDIMM CL46 1.1V Supermicro H14SST-G memory upgrade
- 2TB (16 x 128GB)
- 288-Pin DDR5 RDIMM
Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.
A-Tech
8GB DDR4 2666MHz CL19 1.20V Non-ECC 288-pin DIMM validated for Supermicro systems
This 8GB DDR4 2666MHz DIMM carries Supermicro certification under part number MEM-DR480L-CL01-UN26 and uses Micron components. It is built for desktop systems that require validated memory for stable operation in Supermicro platforms.
The module runs at the JEDEC DDR4 2666 standard with a CL19 latency and 1.20V voltage. Speed and timing are fixed at these values, so the memory will not exceed the PC4-21300 data rate on any motherboard.
Installation follows the standard 288-pin DIMM procedure: align the notch, press firmly until the retention clips lock, and verify seating. The most common issue is a partially seated module that prevents the system from posting.
| Brand | SuperMicro |
|---|---|
| Series | Supermicro Certified |
| Model | MEM-DR480L-CL01-UN26 |
| Capacity | 8GB |
| Speed | DDR4 2666 (PC4 21300) |
| Tested Frequency | 2666 |
| CAS Latency | CL19 |
| Voltage | 1.20V |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Chipset | Micron Chipset |
| Heat Spreader | No |
| Features | Supermicro Certified MEM-DR480L-CL01-UN26 (Micron) |
| Recommend Use | Compatible Supermicro Systems |
This listing is for a single 8GB DDR4 2666MHz module. If your Supermicro system has free DIMM slots, adding one 8GB stick increases total memory by 8GB. For dual-channel performance, install two identical modules in matched slots.
The module runs at 2666 MT/s with CL19 latency at 1.20V. In a compatible Supermicro board it will operate at that rated speed, giving 21300 MB/s peak bandwidth per module. Actual throughput depends on the memory controller and slot population.
The 288-pin DDR4 DIMM interface supports the module's native 2666MHz operation. The board's memory controller and qualified-vendor list determine whether 2666MHz is sustained or downclocked; the DIMM itself is certified for that speed on Supermicro platforms.
Einnig í þessum vöruflokki
Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.
Það sem þú greiðir í, og það sem þú sérð verð í.
Sent úr veskinu þínu í greiðsluferlinu
Aðeins til skýringar — verð í vörulistanum eru í Bandaríkjadölum
Enginn gjaldmiðill passar við það.
Veldu tungumálið sem síðan talar við þig á.
Fyrsta heimsókn?
Áttu þegar aðgang?
Það er engin sjálfvirk endurstilling: þessi verslun sendir engan tölvupóst, svo það er enginn einnota tengill til að biðja um. Skildu netfangið eftir á aðganginum og einhver sinnir því handvirkt.
Beiðni skráð
Ekkert er á leiðinni í pósthólfið þitt — þessi verslun sendir engan tölvupóst. Einhver sinnir þessu handvirkt.
Mundir þú það?