Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Rectangular external liquid cooler with 360 mm copper radiator, six 120 mm fans in push-pull, blue LED base

Alphacool

Alphacool Eiswand 360 CPU External Liquid Cooler

SKU CH-C6A1-2N9NR

External 360 mm radiator with six 700 rpm push-pull fans, dual ceramic pumps and universal CPU block for compact cases

  • TypeAIO
  • Radiator Size360 mm
  • Fan Size3 Fan Slots (120 mm)
  • 360 mm XT45 copper radiator provides high thermal capacity
  • Six 700 rpm Eiswind fans in push-pull deliver strong airflow
  • Dual DC-LT ceramic pumps maintain flow through multiple blocks
  • Includes tubing, fittings and coolant for a complete CPU loop
  • External design fits small cases that cannot mount a 360 mm radiator

Compact external AIO for space-constrained builds

The Alphacool Eiswand 360 is a complete external liquid cooler that sits outside the chassis. It targets builders whose cases cannot fit an internal 360 mm radiator but who still want the thermal capacity of a large copper core and dual pumps. The unit arrives new and ready to assemble into a CPU-focused loop.

Included tubing coolant

The bundle supplies 4 metres of 11/8 mm soft tubing, two 1 litre bottles of Liquid Kelvin Catcher coolant, four anti-kink springs, four black compression fittings and two quick-disconnect fittings. Six 700 rpm Eiswind fans in push-pull and two DC-LT ceramic pumps are pre-installed on the 360 mm XT45 radiator. A universal CPU block and a 90 cm Molex extender complete the kit so no extra parts are required for a single-processor loop.

External mounting avoids case clearance limits but

Because the radiator and pumps reside outside the case, installation only requires routing the supplied tubing through a rear grommet or PCI slot cover and securing the CPU block. The push-pull fan stack and dual-pump assembly are factory-fitted, removing the most error-prone steps of a custom loop. Builders must allocate room for the 360 mm external unit and ensure the Molex extender reaches a power connector; tight tubing bends without the supplied springs are the typical cause of flow restriction.

Helstu kostir

  • 360 mm XT45 copper radiator provides high thermal capacity
  • Six 700 rpm Eiswind fans in push-pull deliver strong airflow
  • Dual DC-LT ceramic pumps maintain flow through multiple blocks
  • Includes tubing, fittings and coolant for a complete CPU loop
  • External design fits small cases that cannot mount a 360 mm radiator

Tæknilýsing

TypeAIO
Radiator Size360 mm
Fan Size3 Fan Slots (120 mm)

Spurningar um þessa vöru

How often should the Liquid Kelvin Catcher coolant be changed in the 360 mm XT45 copper radiator?

The system ships with two 1 L bottles of coolant; refill from this supply whenever the level drops below the pump inlet.

What limits continuous heat removal from the six 700 rpm Eiswind fans in push-pull?

The 360 mm XT45 radiator surface area and the dual DC-LT ceramic pump flow rate set the thermal ceiling.

How much noise and heat do the dual DC-LT ceramic pumps add when the unit runs all day?

The pumps are rated for low-noise operation and the six 700 rpm fans dominate acoustic output at full load.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.