Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Chrome-plated brass Y-connector with two G1/4 threads at 45 degrees

Alphacool

Alphacool G1/4 Revolvable 45° Y-Connector Chrome 17062

SKU CH-15BJ-H7F41

Chrome-finished G1/4 Y-connector splits a liquid-cooling loop at 45° with revolvable threads for parallel component runs

  • ColorChrome
  • FeaturesThis Y-connector can be used for splitting of the cooling lo
  • Splits the loop for parallel component operation
  • Revolvable 45° design eases tube routing in tight spaces
  • High-flow inner diameter reduces restriction for better coolant movement
  • Chrome finish bonded to brass resists peeling over time
  • G1/4 threads accept 10/13/16 mm fittings with noted clearance limits

Loop-splitting Y-connector

The Alphacool G1/4 revolvable 45° Y-connector splits a custom liquid-cooling loop into two parallel paths. It suits builders who need to feed multiple blocks or radiators from a single feed line. The chrome finish matches Alphacool's coordinated fitting range for a uniform look.

Fitting clearance constraint

The connector accepts G1/4 threads with a revolvable 45° angle for flexible routing. Only 10 mm and 13 mm OD fittings sit side by side on the two outlets; 16 mm fittings will interfere with each other. Plan tubing sizes accordingly or stagger the ports to avoid contact.

Brass body with bonded chrome

The fitting body is brass with a chromatised chrome layer bonded to the metal to resist peeling over time. Inner bore is optimised for high flow through the split. Revolvable threads let you orient each outlet independently after tightening. Supplied as a single connector.

Helstu kostir

  • Splits the loop for parallel component operation
  • Revolvable 45° design eases tube routing in tight spaces
  • High-flow inner diameter reduces restriction for better coolant movement
  • Chrome finish bonded to brass resists peeling over time
  • G1/4 threads accept 10/13/16 mm fittings with noted clearance limits

Tæknilýsing

BrandAlphacool
Model64189
ColorChrome
FeaturesThis Y-connector can be used for splitting of the cooling loop to allow parallel operation of cooling components. Please note: 13/10mm fittings just fit side by side. Should 16mm fittings be used, we recommend ordering of an extension or use of 90° angled fittings.

Spurningar um þessa vöru

Should I choose the Chrome, Deep Black or Shiny Copper finish for my loop?

Pick the colour that matches your tubing and other fittings; all three share the same G1/4 revolvable 45° Y geometry and high-flow inner diameter.

What does the 45° Y angle do once the connector is installed?

It splits the loop into two parallel branches at a 45-degree offset, letting you route tubing cleanly while keeping flow restriction low.

How does the G1/4 thread standard limit which compression fittings I can use?

G1/4 is the thread size; 13/10 mm fittings fit side by side, but 16 mm fittings need extra clearance so they may not sit flush together.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.