Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Four black sparkle brass fittings for 14mm rigid tubing

Bitspower

Bitspower BP-BSEMLA14-4P liquid cooler fitting 14mm 4-pack

SKU CH-72S7-NFDDT MPN BP-BSEMLA14-4P

Four G1/4" multi-link compression fittings for 14mm OD hard tubing in Black Sparkle finish

  • TypeFittings
  • Multi-link design enables secure hard-tube extensions
  • 14 mm OD rigid tubing fits precisely into each fitting
  • High-quality brass construction resists corrosion and wear
  • G1/4 inch thread matches standard water-cooling components
  • Four Black Sparkle fittings included for a complete loop

Multi-Link Fittings for 14mm Hard Tubing

These four black sparkle compression fittings are built for custom liquid-cooling loops that use 14mm OD rigid tubing. Each piece is machined from high-quality brass and carries a standard G1/4 thread for direct connection to water blocks, radiators or reservoirs. The pack targets builders who want a clean, expandable hard-line layout without mixing multiple fitting types.

Brass Construction Handles Continuous Pressure

The all-brass bodies resist corrosion and maintain seal integrity during long periods of pump operation and thermal cycling. Compression rings distribute clamping force evenly around the tube, so the joint stays leak-free even when coolant temperature varies across a wide range. RoHS-compliant materials meet restricted-substance requirements for consumer electronics.

Simple Assembly With a Few Common Pitfalls

Slide the compression nut and olive onto the cut tube, push the tube fully into the fitting body, then tighten the nut by hand plus a quarter turn with a wrench. The most frequent errors are leaving the tube end un-chamfered, which prevents a full seat, and over-tightening, which can deform the olive and cause weeping. A light re-check after the first heat cycle eliminates most early leaks.

Helstu kostir

  • Multi-link design enables secure hard-tube extensions
  • 14 mm OD rigid tubing fits precisely into each fitting
  • High-quality brass construction resists corrosion and wear
  • G1/4 inch thread matches standard water-cooling components
  • Four Black Sparkle fittings included for a complete loop

Tæknilýsing

TypeFittings

Spurningar um þessa vöru

How much noise or heat do these four G1/4" brass fittings add when the loop runs all day?

The fittings are passive brass components with no moving parts, so they generate no noise and negligible heat during continuous operation.

What thread size must my existing water blocks, radiators or reservoirs have to accept these fittings?

Every component in the loop needs a G1/4" female port, which is the standard thread these multi-link fittings screw into.

Will the 14 mm OD hard-tube seats in these fittings work with older compression rings or O-rings I already own?

The multi-link design uses its own dedicated sealing rings for 14 mm OD tubing; re-using rings from other brands or sizes is not recommended for a secure seal.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.