Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Aqua duplex multimode fibre patch cable with ST connectors, 3.0 mm jacket

Enfain

Enfain OM3 ST-ST Duplex Multimode Fibre Optic Cable 3.0mm Aqua Blue

SKU CH-GW8J-WEC9T

OM3 duplex multimode patch cable with ST connectors for 10 Gigabit links at 850 nm, 3.0 mm jacket, typical insertion loss .2 dB and return loss >38 dB

Length 1m

  • Supports 10 Gb speeds over OM3 multimode fibre
  • Low 0.2 dB typical insertion loss preserves signal strength
  • High return loss above 38 dB reduces reflections
  • Durable 3.0 mm PVC jacket rated for 1000 mating cycles
  • Operates reliably from -20 °C to 60 °C

Enfain OM3 ST-ST Duplex Multimode Cable

This Enfain OM3 duplex multimode fibre optic cable uses a 3.0 mm PVC jacket and ceramic ferrules. It is built for 10G gigabit links at 850 nm wavelength with ST connectors on both ends. Typical insertion loss is .2 dB and maximum insertion loss is .3 dB, while return loss exceeds 38 dB. It suits data-centre, server and switch patching where OM3 multimode is specified.

Who this suits and who should look elsewhere

Installers needing a pre-terminated OM3 duplex run with ST connectors for 10G, 1G or 40G compatible links will find this cable matches the spec. Buyers who require single-mode fibre, LC or SC connectors, or a different core diameter should choose another product. The 330 mm bending radius and 1000 mating cycles suit managed patch panels but not tight robotics or repeated flexing beyond the rated cycles.

What to check before ordering

Verify that your equipment uses ST connectors and expects OM3 multimode fibre at 850 nm. Confirm the 3.0 mm jacket fits your cable routing and panel density. Ensure the operating range of -20 °C to +60 °C covers your environment. No other interface, protocol or power requirement is implied by this cable.

Helstu kostir

  • Supports 10 Gb speeds over OM3 multimode fibre
  • Low 0.2 dB typical insertion loss preserves signal strength
  • High return loss above 38 dB reduces reflections
  • Durable 3.0 mm PVC jacket rated for 1000 mating cycles
  • Operates reliably from -20 °C to 60 °C

Tæknilýsing

Engin birt tæknilýsing fyrir þessa vöru enn.

Aðrar útgáfur af þessari vöru

5 í viðbót í sama vöruflokki

Sama fjölskylda, mismunandi minni, kælingu eða klukkuhraða — berðu saman áður en þú ákveður þig.

Spurningar um þessa vöru

What equipment must I already have to use this ST duplex cable?

You need devices with ST ports operating at 850 nm that accept multimode duplex fibre, such as switches or servers with ST transceivers.

Can this 3.0 mm OM3 cable run alongside legacy OM1 or OM2 links in the same rack?

Yes, it shares the 850 nm wavelength and ST connectors, so it can coexist with older multimode links, though each link negotiates its own speed.

How do I verify the link is performing to spec after installation?

Measure insertion loss with an 850 nm source and power meter; typical loss should be ≤0.2 dB and maximum ≤0.3 dB, while return loss should exceed 38 dB.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.