Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Gulfe ATX power supply unit, reduced depth, single fan, black finish

Gulfe

Gulfe ATX Power Supply for HP Pavilion P7-1410 P7-1417C

SKU CH-RFBY-J0MV7

ATX replacement unit fits HP Pavilion P7-1410 and P7-1417C desktops with reduced depth and 115/230 V input

  • TypeATX
  • Fans1
  • Weight2.5
  • Replaces legacy HP Pavilion units for P7-1410 and P7-1417C
  • ATX reduced depth of 5.9 inches fits compact cases
  • Dual 115/230 V input works worldwide
  • Over-current and over-power protection safeguards components
  • 24-pin ATX plus 4-pin CPU, three SATA and two LP4 connectors

Replacement Power Supply for HP Pavilion P7-1410

This Gulfe ATX unit is built as a direct replacement for the HP Pavilion P7-1410 and P7-1417C desktop computers. It delivers the standard output rails including +5V, -5V, +12V1, +12V2, +3.3V, -12V, and +5V-SB. The reduced depth of 5.86 inches by 3.3 inches helps it fit inside compact legacy chassis where a full-size ATX supply would not sit properly.

Installation Notes and Common Issues

The supply uses a single cooling fan and weighs 2.5 units, making it straightforward to handle during a swap. Mounting holes follow the standard ATX pattern, but the shorter depth means you must verify the screw alignment against the case standoffs. A frequent issue is forgetting to seat the 24-pin ATX connector fully or missing the separate 4-pin P4-12V plug required for the CPU power rail.

Compatibility Checks Before Ordering

Confirm your system is exactly an HP Pavilion P7-1410 or P7-1417C, as other models may use different connector layouts or mounting positions. Check that the AC input selector on the rear matches your mains supply of 115 V or 230 V. Ensure the chassis can accommodate the 5.9 inch height and 3.4 inch width, and that your drive count matches the three SATA, two LP4, and one floppy connectors provided.

Helstu kostir

  • Replaces legacy HP Pavilion units for P7-1410 and P7-1417C
  • ATX reduced depth of 5.9 inches fits compact cases
  • Dual 115/230 V input works worldwide
  • Over-current and over-power protection safeguards components
  • 24-pin ATX plus 4-pin CPU, three SATA and two LP4 connectors

Tæknilýsing

BrandGulfe
TypeATX
Fans1
Weight2.5

Spurningar um þessa vöru

How can I verify the power supply is working correctly after installing it in my HP Pavilion P7-1410?

The unit should power on with a rise time under 70 ms and maintain output for at least 17 ms hold-up time at nominal load; the single fan should spin and the system must boot stably.

Which cables and connectors come in the box, and what might I need to source separately?

Included are one 24-pin (20+4) ATX connector, one 4-pin P4 12V, three SATA 15-pin, two LP4 4-pin and one floppy 4-pin; any additional GPU or proprietary HP cables are not supplied.

How do I choose between the 115 V and 230 V input settings for my region?

The power supply accepts 115 / 230 V input (110/220 V AC, 47~63 Hz); set the voltage selector switch to match your local mains supply before connecting.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.