Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Green printed circuit board with black memory chips in a standard 288-pin DIMM form factor

OWC

OWC 3U2D41R808GB 8GB DDR4 3200 CL22 1.2V 288-pin UDIMM memory upgrade for Dell OptiPlex 5080 5090 7000 7071

SKU CH-J1JH-SFF92

8GB DDR4 3200 CL22 UDIMM for Dell OptiPlex 5080, 5090, 7000 and 7071 desktops

  • Capacity8GB
  • Type288-Pin DDR4 Non-ECC UDIMM
  • SpeedDDR4 3200 (PC4 25600)
  • CAS LatencyCL22
  • Voltage1.2V
  • ECCNo
  • Designed for Dell OptiPlex 5080 5090 7000 7071 systems
  • 8 GB DDR4 3200 MHz CL22 boosts multitasking speed
  • JEDEC compliant 1.2 V module ensures stable operation
  • Backward compatible with 2133 2400 2666 2933 MHz speeds
  • Simple DIY upgrade installs in standard 288-pin UDIMM slots

8GB DDR4 3200 UDIMM for Dell OptiPlex

This OWC memory module delivers 8GB of DDR4 3200 speed in a 288-pin unbuffered UDIMM form factor. It operates at 1.2V with CL22 latency and is built to JEDEC specifications for reliable operation. The non-ECC design suits standard desktop and workstation platforms.

Suits owners of listed OptiPlex towers and SFFs

Buyers with a Dell OptiPlex 5080 Tower, 5090 SFF, 5090 Tower, 7000 SFF or 7071 Tower can install this module for a direct memory increase. Systems requiring ECC registered memory or a different form factor such as SODIMM cannot use this UDIMM.

Backward compatible with slower DDR4 speeds

The module also runs at 2133, 2400, 2666 and 2933MHz if the platform dictates a lower frequency. This flexibility allows the same part to work across mixed-speed configurations without additional setup. No software or accessories are bundled with the memory.

Helstu kostir

  • Designed for Dell OptiPlex 5080 5090 7000 7071 systems
  • 8 GB DDR4 3200 MHz CL22 boosts multitasking speed
  • JEDEC compliant 1.2 V module ensures stable operation
  • Backward compatible with 2133 2400 2666 2933 MHz speeds
  • Simple DIY upgrade installs in standard 288-pin UDIMM slots

Tæknilýsing

BrandOWC
Part Number3U2D41R808GB
Capacity8GB
Type288-Pin DDR4 Non-ECC UDIMM
SpeedDDR4 3200 (PC4 25600)
CAS LatencyCL22
Voltage1.2V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
Heat SpreaderNo
Compatible SystemDell OptiPlex 5080 Tower
Dell OptiPlex 5090 SFF
Dell OptiPlex 5090 Tower
Dell OptiPlex 7000 SFF
Dell OptiPlex 7071 Tower

Aðrar útgáfur af þessari vöru

5 í viðbót í sama vöruflokki

Sama fjölskylda, mismunandi minni, kælingu eða klukkuhraða — berðu saman áður en þú ákveður þig.

Spurningar um þessa vöru

What type of motherboard slot does this 288-pin DDR4 UDIMM require?

It fits a standard desktop DDR4 DIMM slot on the Dell OptiPlex 5080 Tower, 5090 SFF, 5090 Tower, 7000 SFF or 7071 Tower.

Will this 3200 MHz module run correctly if the system currently has 2133 MHz or 2400 MHz memory installed?

Yes, the module is backward compatible with 2133 MHz, 2400 MHz, 2666 MHz and 2933 MHz speeds and will operate at the highest common frequency supported by the platform.

How can I confirm the CL22 1.2V module is recognised at the correct speed after installation?

Open Task Manager or BIOS and verify the memory reports 3200 MHz (PC4-25600) with 8 GB capacity and non-ECC unbuffered operation.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.