Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Green OWC 4GB DDR3 240-pin UDIMM module, no heat spreader

OWC

OWC 4GB DDR3 1600 PC3-12800 CL11 1Rx8 240-pin 1.5V Non-ECC UDIMM Dell OptiPlex 7010 memory upgrade

SKU CH-NMNQ-KEX6X

A 4GB DDR3 1600 module upgrades Dell OptiPlex 7010 desktops with 1.5V non-ECC memory

  • Capacity4GB
  • Type240-Pin DDR3 Non-ECC UDIMM
  • SpeedDDR3 1600 (PC3 12800)
  • CAS LatencyCL11
  • Voltage1.5V
  • ECCNo
  • Boosts system responsiveness with a 4GB DDR3 1600MHz module
  • Guaranteed fit for Dell OptiPlex 7010 Desktop, SFF, Tower and USFF
  • Meets JEDEC and RoHS standards for a warranty-safe upgrade
  • Simple DIY installation with unbuffered 240-pin DIMM design
  • Reliable operation at standard 1.5V with CL11 latency

4GB DDR3 module for Dell OptiPlex 7010

This 4GB DDR3 1600 PC3-12800 CL11 UDIMM is built specifically for Dell OptiPlex 7010 Desktop, SFF, Tower and USFF systems. It operates at 1.5V with unbuffered, non-ECC architecture and a single 1Rx8 rank. The 240-pin form factor matches the factory DIMM slots exactly.

JEDEC-standard timing under sustained load

Rated at CL11 latency and 1600 MHz, the module maintains its specified timing during extended workloads rather than only in short bursts. JEDEC and RoHS compliance ensures the electrical parameters stay within the original Dell qualification envelope for continuous operation.

Low-voltage operation without a heat spreader

At 1.5V the module draws minimal power and runs cool enough to omit a heat spreader, keeping the profile slim for tight SFF and USFF chassis. The unbuffered design adds no active components, so acoustic output remains that of the system fans alone.

Helstu kostir

  • Boosts system responsiveness with a 4GB DDR3 1600MHz module
  • Guaranteed fit for Dell OptiPlex 7010 Desktop, SFF, Tower and USFF
  • Meets JEDEC and RoHS standards for a warranty-safe upgrade
  • Simple DIY installation with unbuffered 240-pin DIMM design
  • Reliable operation at standard 1.5V with CL11 latency

Tæknilýsing

BrandOWC
Part Number1U6D31R804GB
Capacity4GB
Type240-Pin DDR3 Non-ECC UDIMM
SpeedDDR3 1600 (PC3 12800)
CAS LatencyCL11
Voltage1.5V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
Heat SpreaderNo
Compatible SystemDell OptiPlex 7010 Desktop
Dell OptiPlex 7010 SFF
Dell OptiPlex 7010 Tower
Dell OptiPlex 7010 USFF

Aðrar útgáfur af þessari vöru

5 í viðbót í sama vöruflokki

Sama fjölskylda, mismunandi minni, kælingu eða klukkuhraða — berðu saman áður en þú ákveður þig.

Spurningar um þessa vöru

Does the 1.5V DDR3 module run hot or draw extra power during all-day use?

The JEDEC-standard 1.5V DDR3 UDIMM operates at the normal voltage for this generation, so heat and power draw stay within typical desktop limits.

What must the Dell OptiPlex 7010 already have to accept this 240-pin UDIMM?

A free 240-pin DDR3 DIMM slot on the motherboard is the only requirement; the module is unbuffered, non-ECC and matches the system's native PC3-12800 CL11 timing.

Will this CL11 1600MHz stick work alongside the original memory in a 7010 Tower?

Yes, it is tested to meet Dell OEM specs for the OptiPlex 7010 family, so it will run at the system's default speed alongside existing modules.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.