Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Green circuit board with one SATA input and five SATA output ports

SMUGDESK

SMUGDESK 1 to 5 Port SATA 3.0 Expansion Card

SKU CH-J3QW-0C3EX

Adds five SATA 3.0 ports through one motherboard connection for HDD and SSD expansion

  • Expands one motherboard SATA port into five drive connections
  • SATA 3.0 standard delivers up to 6Gbps transfer speed for HDDs and SSDs
  • Compact riser hub fits standard desktop cases for easy internal installation
  • Works with mechanical drives, solid-state drives and storage enclosures
  • Shared bandwidth across all ports suits DIY PCs, file servers and storage upgrades

1-to-5 SATA Port Multiplier

This SMUGDESK expansion card turns one motherboard SATA interface into five, letting desktop users add multiple hard drives or SSDs when onboard ports are exhausted. It targets DIY builders, video creators and small file-server operators who need extra internal storage without replacing the board. The adapter works with mechanical drives, solid-state drives and compatible storage enclosures. Installation fits standard desktop chassis for a straightforward internal upgrade.

Sustained Throughput on Shared Bandwidth

The card follows the SATA 3.0 specification with a 6Gbps ceiling that is divided among all attached drives during simultaneous access. Sequential reads and writes remain steady for archival, media libraries and light server workloads, but peak throughput per drive drops as more disks operate at once. Heavy multi-drive arrays will see each device share the total pipe rather than enjoy the full link speed. A stable, adequately rated power supply is required so that every connected drive spins up and stays recognised under load.

Compact Riser Hub Build

A low-profile riser board slips into tight case spaces and connects directly to a single motherboard SATA header, leaving other expansion slots free. Five outward-facing SATA ports accept standard data cables for clean cable routing inside the chassis. The design assumes the host system can deliver enough current for several drives; builders with limited power-headroom or only one free SATA header should verify their platform can support the additional load before committing.

Helstu kostir

  • Expands one motherboard SATA port into five drive connections
  • SATA 3.0 standard delivers up to 6Gbps transfer speed for HDDs and SSDs
  • Compact riser hub fits standard desktop cases for easy internal installation
  • Works with mechanical drives, solid-state drives and storage enclosures
  • Shared bandwidth across all ports suits DIY PCs, file servers and storage upgrades

Tæknilýsing

Engin birt tæknilýsing fyrir þessa vöru enn.

Spurningar um þessa vöru

Does the SATA 3.0 card run hot or draw extra power when all five drives are active all day?

The multiplier hub itself has no active cooling and draws minimal power; sustained heat and current depend on the drives you attach and your PSU capacity.

What must my motherboard already have so this 1-to-5 adapter works?

A free SATA 3.0 port on the motherboard and an available power connector from the PSU for the drives.

Will my older SATA II hard drives work at full speed on this SATA 3.0 multiplier?

Yes, SATA II drives are backward compatible and will operate at their native 3Gbps rate while sharing the single 6Gbps upstream link.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.