Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Green circuit board with gold edge connector and two mounting brackets

Syba

Syba SI-ADA50067 M.2 & mSATA to SATA expansion card

SKU CH-GGTK-TTQFR MPN SI-ADA50067

Connects M.2 or mSATA SSDs to a SATA port at 6.0 Gbps with standard and low-profile brackets

  • Data Transfer Rate6.0 Gbps
  • FeaturesM.2 Specification revision 0.9 Serial ATA Specification revi
  • Dimensions1.50" x 5.50" x 7.00" (H x W x L)
  • Weight1
  • Package Contents1 x M.2 and mSATA to SATA III Adapter 1 x User Manual 1 x Lo
  • Connect M.2 or mSATA SSDs to a standard SATA port
  • Achieve 6.0 Gbps data transfer with SATA 3.2 support
  • Fit 22 mm wide M.2 cards in 30, 42 or 60 mm lengths
  • Includes low-profile bracket for small-form-factor builds
  • Supports M.2 B-key modules for broad SSD compatibility

M.2 and mSATA to SATA III adapter

The Syba SI-ADA50067 connects an M.2 (NGFF) or mSATA solid-state drive to a standard SATA interface. It supports M.2 B-key cards in 22*30, 22*42 and 22*60 sizes as well as mSATA SSDs measuring 26.8*30 and 50.95*30. The card operates at SATA revision 3.2 with a 6.0 Gbps data transfer rate. Both standard and low-profile brackets are included for different chassis types.

Builders adding SATA-based M.2 or mSATA storage

This adapter suits builders who want to install a SATA-protocol M.2 or mSATA SSD in a system with a free SATA port. It also supports system boot from the attached drive. Buyers who need to install a PCIe-based M.2 drive cannot use this adapter because it operates only over the SATA protocol. Systems without an available SATA connector or without space for a full-height or low-profile expansion card should look at other solutions.

SATA revision 3.2 at 6.0 Gbps

The single specification that decides compatibility is the SATA revision 3.2 interface running at 6.0 Gbps. Only M.2 B-key or mSATA drives that communicate over the SATA protocol will function; PCIe-based M.2 modules are not supported. Verify that the drive uses the SATA protocol and matches the listed physical dimensions before purchase.

Helstu kostir

  • Connect M.2 or mSATA SSDs to a standard SATA port
  • Achieve 6.0 Gbps data transfer with SATA 3.2 support
  • Fit 22 mm wide M.2 cards in 30, 42 or 60 mm lengths
  • Includes low-profile bracket for small-form-factor builds
  • Supports M.2 B-key modules for broad SSD compatibility

Tæknilýsing

BrandSYBA
ModelSI-ADA50067
Data Transfer Rate6.0 Gbps
FeaturesM.2 Specification revision 0.9
Serial ATA Specification revision 3.2
Supports M.2 card sizes:
22*30
22*42
22*60
Supports mSATA SSD size:
26.8*30
50.95*30
Supports M.2 B Key Card Type
Support highspeed SATA3/6 Gbps interface
52-pin mini PCIe interface
Compatible with SATA revision 2.6
Support ATA/ATAP-7 Specification
An M.2 SSD will always be the first priority. When both an M.2 and mSATA device are connected the mSATA will not funciton.
Dimensions1.50" x 5.50" x 7.00" (H x W x L)
Weight1
Package Contents1 x M.2 and mSATA to SATA III Adapter
1 x User Manual
1 x Low Profile Bracket
1 x Bag of screws and washers
Sendingarþyngd0.09 kg
Stærð sendingar178 × 140 × 41 mm

Spurningar um þessa vöru

Does my motherboard need a free SATA port and cable for this adapter?

Yes, the card converts an M.2 or mSATA SSD to a standard SATA III connection running at 6.0 Gbps, so an available SATA port and data cable are required.

Can I keep using an older SATA II drive on the same controller while this card runs at SATA III speed?

The adapter operates at SATA revision 3.2 with a 6.0 Gbps transfer rate, and SATA is backward compatible, so legacy SATA II devices will continue to work on the same controller.

How do I confirm the M.2 SSD is recognised after installing it on the SI-ADA50067?

After securing the M.2 drive (22*30, 22*42 or 22*60) with the supplied screws, the SSD should appear in BIOS and the operating system as a normal SATA storage device.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.