Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Five stainless steel heat breaks, M6 and M7 threads, 22.5 mm long, for 1.75 mm filament

Unique-Bargains

Unique-Bargains M6x22.5mm 1.75mm Throat Tube V6 Makerbot 3D Printer Accessory 5pcs

SKU CH-TZ3Q-3NFET

Pack of five stainless-steel heat-break tubes with M7 and M6 threads for 1.75 mm filament on V6 Makerbot printers

  • Fits V6 Makerbot printers with M7 and M6 threaded heat break
  • Guides 1.75 mm PLA and ABS filament through 4 mm and 2 mm bore
  • Stainless steel throat resists wear during long print sessions
  • 5 mm length matches standard V6 hot-end geometry
  • Five pieces included for quick replacement or multi-printer setups

Five stainless-steel heat breaks for V6 hot-ends

This pack contains five M6 x 22.5 mm throat tubes with a 1.75 mm bore, made from stainless steel and designed to fit V6-style hot-ends on Makerbot 3D printers. The middle section uses M7x1 threads while the lower section that seats in the heater block uses M6x1 threads.

Makers running 1.75 mm PLA

These heat breaks suit owners of V6-style extruders who need replacement or spare throat tubes for 1.75 mm filament. Printers that require a different thread pattern, a different throat length or a larger filament diameter will not accept these parts.

M7x1 upper thread with M6x1 lower thread

The critical specification is the dual-thread profile: M7x1 on the middle portion and M6x1 at the base that enters the heater block. Verify that your hot-end uses this exact thread combination before ordering.

Helstu kostir

  • Fits V6 Makerbot printers with M7 and M6 threaded heat break
  • Guides 1.75 mm PLA and ABS filament through 4 mm and 2 mm bore
  • Stainless steel throat resists wear during long print sessions
  • 5 mm length matches standard V6 hot-end geometry
  • Five pieces included for quick replacement or multi-printer setups

Tæknilýsing

BrandUnique Bargains

Spurningar um þessa vöru

Should I pick the 5-piece pack or is there a single throat tube option available?

The listing only offers a 5-piece pack of stainless steel throat tubes for V6 Makerbot printers.

What does the 1.75 mm filament rating mean when the tube is installed in my hotend?

The 1.75 mm rating confirms the tube inner bore matches standard 1.75 mm PLA or ABS filament for reliable feeding.

How do the M7 and M6 threads on this heat break affect which heater block I can use?

The middle section uses M7x1 threads for the heat sink while the base uses M6x1 threads that screw into the heater block.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.