Mēs pieņemam kriptovalūtu — lai tā, kas Jums pieder, varētu nopirkt īstu aparatūru.Maksājiet kriptovalūtā, iztērējiet to īstai aparatūrai. Bezmaksas apdrošināta piegāde visā pasaulē virs 399 $. Vienkāršas, nemarķētas kastes, sūtītas no Vācijas.Bezmaksas apdrošināta piegāde virs 399 $. Jūsu kurss tiek fiksēts uz 30 minūtēm, tiklīdz atveras kase.Kurss fiksēts uz 30 minūtēm. Katra prece ir aizzīmogota, tās sērijas numurs ir pārbaudīts, un uz to attiecas 24 mēnešu garantija.Aizzīmogots, 24 mēnešu garantija.

Uzraudzītās preces Pieteikties
Spool of grey 3D printing filament on a reel

E3D Online

E3D Online spoolWorks EDGE Filament 1.75mm 750g Cement Grey 3D Printers Accessories

SKU CH-FSZT-A1CCC

1.75 mm PETG-based filament in Cement Grey, 750 g spool, combining ABS toughness with PLA ease of use for low-warp prints

  • ColorGray
  • TypeFilament
  • Recyclable PETG-based material reduces environmental impact
  • Easy printing with no unpleasant fumes or odors
  • Strong tough naturally glossy finish for durable parts
  • Adheres to bed surfaces with just a little gluestick
  • Pairs with Scaffold support for reliable adhesion clean breakaway

Filament type and weight

E3D spoolWorks EDGE is a PETG-based filament supplied as a 750 g spool in 1.75 mm diameter. It is formulated for makers who want the toughness of ABS with the ease of printing associated with PLA. The material produces naturally glossy parts and emits no unpleasant fumes during extrusion. It suits functional prototypes and end-use parts that require durability.

Behaviour during long prints

Edge exhibits super-low contraction, which E3D developed to nearly eliminate warping over extended builds. Managed viscosity, adhesion and melt strength allow accurate overhangs and tight bridges to hold their geometry layer after layer. Layer bonding reaches near-isotropic strength so parts stay tough across the Z axis. The spool is fully recyclable after use.

Compatibility checks before ordering

Confirm that your printer accepts 1.75 mm filament and that the extruder can reach PETG printing temperatures. A heated bed and a light coating of gluestick are recommended for first-layer adhesion. If you plan to use soluble or breakaway supports, verify that your slicer profile supports the Scaffold material pairing. The grey colour may affect visual inspection of fine details.

Priekšrocības

  • Recyclable PETG-based material reduces environmental impact
  • Easy printing with no unpleasant fumes or odors
  • Strong tough naturally glossy finish for durable parts
  • Adheres to bed surfaces with just a little gluestick
  • Pairs with Scaffold support for reliable adhesion clean breakaway

Specifikācijas

BrandE3D
ModelEdge
ColorGray
TypeFilament

Jautājumi par šo preci

Does the 1.75 mm Edge filament produce noticeable fumes or heat during long prints?

The material is designed to print with no unpleasant fumes or odours, keeping the printing area comfortable during extended sessions.

What bed surface or adhesive is required for the 750 g spool to stick reliably?

It adheres effectively to common bed surfaces using only a thin layer of gluestick, so no special coatings or tapes are needed.

Can the Edge filament be used with older printers that only handle PLA or ABS?

Yes, it combines ABS-like toughness with PLA-like ease of use and has super-low contraction, making it suitable for machines calibrated for either material.

Arī šajā sadaļā

Klienti arī salīdzināja

Tas pats plaukts, tā pati kase — astoņas kriptovalūtas un kursa fiksēšana uz 30 minūtēm.