Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Spool of grey 3D printing filament on a reel

E3D Online

E3D Online spoolWorks EDGE Filament 1.75mm 750g Cement Grey 3D Printers Accessories

SKU CH-FSZT-A1CCC

1.75 mm PETG-based filament in Cement Grey, 750 g spool, combining ABS toughness with PLA ease of use for low-warp prints

  • ColorGray
  • TypeFilament
  • Recyclable PETG-based material reduces environmental impact
  • Easy printing with no unpleasant fumes or odors
  • Strong tough naturally glossy finish for durable parts
  • Adheres to bed surfaces with just a little gluestick
  • Pairs with Scaffold support for reliable adhesion clean breakaway

Filament type and weight

E3D spoolWorks EDGE is a PETG-based filament supplied as a 750 g spool in 1.75 mm diameter. It is formulated for makers who want the toughness of ABS with the ease of printing associated with PLA. The material produces naturally glossy parts and emits no unpleasant fumes during extrusion. It suits functional prototypes and end-use parts that require durability.

Behaviour during long prints

Edge exhibits super-low contraction, which E3D developed to nearly eliminate warping over extended builds. Managed viscosity, adhesion and melt strength allow accurate overhangs and tight bridges to hold their geometry layer after layer. Layer bonding reaches near-isotropic strength so parts stay tough across the Z axis. The spool is fully recyclable after use.

Compatibility checks before ordering

Confirm that your printer accepts 1.75 mm filament and that the extruder can reach PETG printing temperatures. A heated bed and a light coating of gluestick are recommended for first-layer adhesion. If you plan to use soluble or breakaway supports, verify that your slicer profile supports the Scaffold material pairing. The grey colour may affect visual inspection of fine details.

Kohokohdat

  • Recyclable PETG-based material reduces environmental impact
  • Easy printing with no unpleasant fumes or odors
  • Strong tough naturally glossy finish for durable parts
  • Adheres to bed surfaces with just a little gluestick
  • Pairs with Scaffold support for reliable adhesion clean breakaway

Tekniset tiedot

BrandE3D
ModelEdge
ColorGray
TypeFilament

Kysymyksiä tästä tuotteesta

Does the 1.75 mm Edge filament produce noticeable fumes or heat during long prints?

The material is designed to print with no unpleasant fumes or odours, keeping the printing area comfortable during extended sessions.

What bed surface or adhesive is required for the 750 g spool to stick reliably?

It adheres effectively to common bed surfaces using only a thin layer of gluestick, so no special coatings or tapes are needed.

Can the Edge filament be used with older printers that only handle PLA or ABS?

Yes, it combines ABS-like toughness with PLA-like ease of use and has super-low contraction, making it suitable for machines calibrated for either material.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.