Mēs pieņemam kriptovalūtu — lai tā, kas Jums pieder, varētu nopirkt īstu aparatūru.Maksājiet kriptovalūtā, iztērējiet to īstai aparatūrai. Bezmaksas apdrošināta piegāde visā pasaulē virs 399 $. Vienkāršas, nemarķētas kastes, sūtītas no Vācijas.Bezmaksas apdrošināta piegāde virs 399 $. Jūsu kurss tiek fiksēts uz 30 minūtēm, tiklīdz atveras kase.Kurss fiksēts uz 30 minūtēm. Katra prece ir aizzīmogota, tās sērijas numurs ir pārbaudīts, un uz to attiecas 24 mēnešu garantija.Aizzīmogots, 24 mēnešu garantija.

Uzraudzītās preces Pieteikties
Green circuit board with silver M.2 slot and 40-pin GPIO header, PoE circuitry visible

LORDWORLD

LORDWORLD PCIe to M.2 Adapter with PoE HAT for Raspberry Pi 5 NVMe SSD 2230/2242 IEEE 802.3af/at

SKU CH-XBFG-27694

Adds NVMe storage and PoE power to a Raspberry Pi 5 via its 16-pin PCIe interface, supports 2230 and 2242 drives, and keeps the 40-pin GPIO header free for other HATs

  • Adds NVMe storage to Raspberry Pi 5 via 16-pin PCIe
  • Powers Pi 5 through IEEE 802.3af/at PoE network standard
  • Stackable 40-pin GPIO header keeps expansion options open
  • Dual onboard LEDs show drive and power status at a glance
  • Fits 2230 or 2242 M.2 drives and supports booting from SSD

Raspberry Pi 5 NVMe adapter with PoE HAT

This expansion board connects to the Raspberry Pi 5 through its 16-pin PCIe interface and provides a 40-pin stackable GPIO header for additional HATs. It accepts M.2 2230 and 2242 solid-state drives that use the NVMe protocol. The board also includes Power over Ethernet support compliant with IEEE 802.3 af/at standards, allowing the Pi to be powered through a network cable.

Sustained NVMe throughput and thermal behaviour

Under continuous read or write workloads the adapter runs at the speed negotiated by the drive in Gen2 or Gen3 mode. Dual onboard LEDs give immediate visual feedback on drive activity and power status. Because the board has no active cooling, prolonged heavy I/O will be limited by the thermal envelope of the specific M.2 module installed.

M.2 form-factor and PoE power constraints

Only 2230 and 2242 length drives are physically supported; longer 2280 modules cannot be fitted. The PoE input follows IEEE 802.3 af/at so the available power budget depends on the class of the power sourcing equipment. Drives with unusually high peak current demands may exceed what the HAT can deliver through the Pi's PCIe connector.

Priekšrocības

  • Adds NVMe storage to Raspberry Pi 5 via 16-pin PCIe
  • Powers Pi 5 through IEEE 802.3af/at PoE network standard
  • Stackable 40-pin GPIO header keeps expansion options open
  • Dual onboard LEDs show drive and power status at a glance
  • Fits 2230 or 2242 M.2 drives and supports booting from SSD

Specifikācijas

BrandLORDWORLD

Jautājumi par šo preci

How much power does the PoE HAT draw when the Pi 5 and NVMe SSD run continuously?

The HAT supports IEEE 802.3af/at so it can draw up to the standard limits, but exact consumption depends on the SSD and Pi 5 load.

What else must I already own to use this adapter with a Raspberry Pi 5?

You need a Raspberry Pi 5 with its 16-pin PCIe connector and a 40-pin GPIO header, plus an M.2 NVMe SSD in 2230 or 2242 size.

Can I keep using my existing HATs that sit on the 40-pin GPIO header?

Yes, the board includes a stackable 40-pin GPIO header so other HATs can be mounted on top.

Arī šajā sadaļā

Klienti arī salīdzināja

Tas pats plaukts, tā pati kase — astoņas kriptovalūtas un kursa fiksēšana uz 30 minūtēm.