BFKK
BFKK 3U Rackmount Server Chassis EATX/ATX/MATX 4x5.25 6x3.5 Top/Side Cooling
- Rackmount
214,99 $
0.0027816BTC
Krājumā
NEMIX RAM
NEMIX RAM 16GB DDR4 3200 CL22 2Rx8 1.2V UDIMM for THINKMATE XF6-14X1
16 GB DDR4 3200 CL22 2Rx8 1.2 V UDIMM built for THINKMATE XF6-14X1 workstations
- Capacity16GB
- SpeedDDR4 3200 (PC4 25600)
- ECCNo
- Buffered/RegisteredUnbuffered
- ChipsetMajor OEM Samsung, Micron, Hynix
- Voltage1.20V
- 16 GB DDR4-3200 boosts workstation throughput
- CL22 latency at 1.2 V keeps power draw low
- 2Rx8 dual-rank layout fills a single DIMM slot
- 288-pin UDIMM fits ThinkMate XF6-14X1 without adapters
- Major OEM chips stress-tested for enterprise stability
NEMIX RAM 16GB DDR4 3200 for Thinkmate XF6-14X1
This NEMIX RAM module provides 16GB of DDR4 3200 memory in a single 288-pin UDIMM. It runs at 1.20V with CL22 latency and a 2Rx8 rank configuration. The memory uses major OEM chips from Samsung, Micron or Hynix and is validated for the Thinkmate XF6-14X1 workstation. No heat spreader is included.
Who this suits and who should look elsewhere
This module suits owners of a Thinkmate XF6-14X1 workstation needing a 16GB DDR4 3200 upgrade. It is non-ECC and unbuffered so it will not work in systems that require registered or ECC memory. Buyers who need error-correcting code support or registered DIMMs should look elsewhere.
What the package contents change
The package contains one 16GB UDIMM and nothing else. No software, cables or additional accessories are bundled. The memory arrives ready to install in a compatible motherboard slot.
Priekšrocības
- 16 GB DDR4-3200 boosts workstation throughput
- CL22 latency at 1.2 V keeps power draw low
- 2Rx8 dual-rank layout fills a single DIMM slot
- 288-pin UDIMM fits ThinkMate XF6-14X1 without adapters
- Major OEM chips stress-tested for enterprise stability
Specifikācijas
| Brand | NEMIX RAM |
|---|---|
| Series | THINKMATE Server/Workstation Compatible Series Memory |
| Model | THINKMATE DDR4 3200MHZ Non-ECC Unbuffered UDIMM |
| Part Number | MD25600-628K1 |
| Capacity | 16GB |
| Speed | DDR4 3200 (PC4 25600) |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Chipset | Major OEM Samsung, Micron, Hynix |
| Voltage | 1.20V |
| Compatible System | THINKMATE |
| CAS Latency | CL22 |
| Heat Spreader | No |
| Type | 288-Pin DDR4 UDIMM |
| Rank | 2Rx8 |
| Features | DDR4 Non- ECC Unbuffered UDIMM Motherboard Compatible |
| Package Content | 16GB (1X16GB) DDR4 3200MHZ PC4-25600 2Rx8 1.2V CL22 288-PIN Non-ECC Unbuffered UDIMM |
Jautājumi par šo preci
Does my THINKMATE XF6-14X1 need a free 288-pin DDR4 UDIMM slot to accept this 16GB module?
Yes, the module uses the standard 288-pin DDR4 UDIMM form factor, so an available DDR4 UDIMM slot on the XF6-14X1 motherboard is required for installation.
Will this 3200 MHz CL22 2Rx8 module run at its rated speed if I keep slower DDR4 sticks in the other slots?
The system will typically downclock all modules to the speed of the slowest installed stick, so this 3200 MHz module would run at the lower frequency of the older modules.
How can I confirm the module is recognised at 3200 MHz with CL22 timings after I install it?
Check the memory speed and CAS latency in the BIOS setup or use a tool such as CPU-Z to verify the module reports 3200 MHz and CL22 timings.
Arī šajā sadaļā
Klienti arī salīdzināja
Tas pats plaukts, tā pati kase — astoņas kriptovalūtas un kursa fiksēšana uz 30 minūtēm.
