SanDisk
SanDisk Cruzer Blade 8 GB USB 2.0 USB flash drive Black SDCZ50-008G-B35
USD 391.99
0.00499179BTC
Ada stok
NEMIX RAM
NEMIX RAM DDR5 6400 96GB 2x48GB CL52 1.1V ECC RDIMM Supermicro H14DST-FL memory upgrade
A 96 GB DDR5-6400 ECC registered kit (2 × 48 GB, CL52, 1.1 V, 288-pin) validated for the Supermicro H14DST-FL motherboard
- Capacity96GB (2 x 48GB)
- Type288-Pin DDR5 RDIMM
- SpeedDDR5 6400 (PC5 51200)
- CAS LatencyCL52
- Voltage1.10V
- ECCYes
- 96 GB capacity from two 48 GB modules for dense server memory configurations
- DDR5 6400 speed with CL52 latency delivers rated throughput on supported platforms
- Registered ECC design corrects single-bit errors and stabilises fully populated slots
- 1 V operation matches the motherboard's memory controller specification exactly
- 288-pin RDIMM form factor fits the Supermicro H14DST-FL memory sockets precisely
96 GB DDR5-6400 ECC RDIMM kit for Supermicro
This 96 GB kit contains two 48 GB DDR5-6400 registered ECC RDIMMs rated at CL52 and 1.1 V. The modules use a 288-pin form factor and a 2Rx8 organisation built with major OEM chips. They are specified as an exact-match upgrade for the Supermicro H14DST-FL motherboard.
Suited for registered ECC servers.
This memory suits administrators populating a Supermicro H14DST-FL with registered ECC DIMMs that the board's memory controller expects. Builders needing unbuffered UDIMMs, SODIMMs or non-ECC modules for workstations or consumer boards should look elsewhere because the registered design and pin-out are incompatible with those platforms.
288-pin registered ECC DDR5 RDIMM form factor
The single specification that decides fitment is the 288-pin registered ECC DDR5 RDIMM form factor required by the Supermicro H14DST-FL. Only modules matching this exact registered RDIMM design, voltage and pin count will be recognised at full capacity and run at the rated 6400 MT/s speed.
Ciri-ciri utama
- 96 GB capacity from two 48 GB modules for dense server memory configurations
- DDR5 6400 speed with CL52 latency delivers rated throughput on supported platforms
- Registered ECC design corrects single-bit errors and stabilises fully populated slots
- 1 V operation matches the motherboard's memory controller specification exactly
- 288-pin RDIMM form factor fits the Supermicro H14DST-FL memory sockets precisely
Spesifikasi
| Brand | NEMIX RAM |
|---|---|
| Series | NEMIX RAM Original Series Server Memory |
| Model | DDR5 ECC RDIMM Registered Server Memory |
| Part Number | MR51200-4828K2 |
| Capacity | 96GB (2 x 48GB) |
| Type | 288-Pin DDR5 RDIMM |
| Speed | DDR5 6400 (PC5 51200) |
| CAS Latency | CL52 |
| Voltage | 1.10V |
| ECC | Yes |
| Buffered/Registered | Registered |
| Rank | 2Rx8 |
| Chipset | Major OEM Samsung, Micron, Hynix |
| Heat Spreader | No |
| Compatible System | Supermicro |
| Features | DDR5 ECC RDIMM Motherboard Compatible |
| Package Content | 96GB 2X48GB DDR5 6400MHz PC5-51200 2Rx8 1.1V 288-PIN ECC RDIMM KIT |
Soalan tentang produk ini
Must my Supermicro H14DST-FL motherboard already support 288-pin DDR5 RDIMM slots for this 96GB kit to work?
Yes, the H14DST-FL requires 288-pin Registered DDR5 DIMMs; this kit matches that exact form factor and will not fit UDIMM or SODIMM slots.
Will the 2Rx8 registered ECC modules run at the rated 6400 speed alongside any older DDR5 DIMMs I keep in the same server?
Mixing ranks or speeds forces the memory controller to run all slots at the lowest common speed and may break the board's population rules; the manual should be checked before combining kits.
How can I confirm the kit is operating at CL52 and 1.10 V after installation?
Enter the BIOS or use a hardware-monitoring utility to verify the memory frequency shows 6400 MT/s, CAS latency reads 52, and DRAM voltage reports 1.10 V.
Juga di rak ini
Pelanggan turut membandingkan
Rak yang sama, checkout yang sama — lapan koin kripto dan kunci kadar 30 minit.
SAMSUNG
SAMSUNG M393A1K43DB2-CWE DDR4-3200 8GB ECC Registered server RAM
USD 74.99
0.00095496BTC
Ada stok