Kami menerima kripto — jadi koin yang anda simpan boleh membeli perkakasan sebenar.Bayar dengan kripto, belanjakannya untuk perkakasan sebenar. Penghantaran berinsurans percuma ke seluruh dunia untuk belian melebihi USD 399. Kotak biasa tanpa jenama, dihantar dari Jerman.Penghantaran berinsurans percuma untuk belian melebihi USD 399. Kadar anda dikunci selama 30 minit sebaik sahaja proses pesanan bermula.Kadar dikunci selama 30 minit. Setiap item disegel, nombor sirinya disemak, dan dilindungi waranti 24 bulan.Disegel, waranti 24 bulan.

Barang disimpan Log masuk
Green printed circuit board with black memory chips and gold edge connectors

OWC

OWC 4GB DDR3 1600 PC3-12800 CL11 1Rx8 240-pin 1.5V Non-ECC UDIMM memory upgrade

SKU CH-4E34-5NK50

A 4 GB DDR3 1600 UDIMM upgrade for compatible HP EliteDesk 700 and 705 systems

  • Capacity4GB
  • Type240-Pin DDR3 Non-ECC UDIMM
  • SpeedDDR3 1600 (PC3 12800)
  • CAS LatencyCL11
  • Voltage1.5V
  • ECCNo
  • Boosts multitasking with a 4GB DDR3 1600 module
  • JEDEC-standard 1.5V CL11 spec ensures broad compatibility
  • Single 1Rx8 rank simplifies installation in supported HP desktops
  • Unbuffered non-ECC design matches factory memory requirements
  • Tested for HP EliteDesk 700 G1 and 705 G1/G2 systems

4GB DDR3 1600 UDIMM for HP EliteDesk

This single 4GB DDR3 module runs at 1600 MHz with CL11 latency and 1.5V operation. It uses a 240-pin unbuffered non-ECC design built to JEDEC standards. The kit targets owners of HP EliteDesk 700 G1 SFF, 700 G1 Tower, 705 G1 SFF, 705 G1 Tower and 705 G2 SFF systems seeking a straightforward capacity increase.

Who this suits and who should look elsewhere

The module suits users upgrading the listed EliteDesk models where a 240-pin DDR3 DIMM is required. Builders needing ECC error correction, registered signalling, voltages other than 1.5V, or capacities beyond 4GB per slot should look elsewhere. Systems that accept only SODIMM form factors or a different pin count are also incompatible.

Deciding specification — 240-pin DDR3 1600 CL11 1.5V

The decisive factor is the 240-pin DDR3 interface running at 1600 MHz with CL11 timing at 1.5V. Verify that the target motherboard specifies this exact speed, voltage and pin layout before purchase; a mismatch in any of those parameters will prevent the module from functioning.

Ciri-ciri utama

  • Boosts multitasking with a 4GB DDR3 1600 module
  • JEDEC-standard 1.5V CL11 spec ensures broad compatibility
  • Single 1Rx8 rank simplifies installation in supported HP desktops
  • Unbuffered non-ECC design matches factory memory requirements
  • Tested for HP EliteDesk 700 G1 and 705 G1/G2 systems

Spesifikasi

BrandOWC
Part Number1U6D31R804GB
Capacity4GB
Type240-Pin DDR3 Non-ECC UDIMM
SpeedDDR3 1600 (PC3 12800)
CAS LatencyCL11
Voltage1.5V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
Heat SpreaderNo
Compatible SystemHP EliteDesk 700 G1 SFF
HP EliteDesk 700 G1 Tower
HP EliteDesk 705 G1 SFF
HP EliteDesk 705 G1 Tower
HP EliteDesk 705 G2 SFF

Versi lain model ini

5 lagi dalam julat yang sama

Keluarga yang sama, memori, penyejuk atau kelajuan jam yang berbeza — bandingkan sebelum membuat keputusan.

Soalan tentang produk ini

Does this 240-pin DDR3 UDIMM need a motherboard with a 240-pin DDR3 slot?

Yes, it fits a standard 240-pin DDR3 DIMM socket on a desktop or workstation board.

Can I add this 1.5 V CL11 module to an HP EliteDesk 700 G1 that already has memory installed?

The module is tested for those EliteDesk models and will run at the speed of the slowest installed stick.

How do I confirm the 4 GB stick is recognised at PC3-12800 after fitting it?

Check the BIOS memory summary or Windows Task Manager to see 4 GB at 1600 MHz CL11.

Juga di rak ini

Pelanggan turut membandingkan

Rak yang sama, checkout yang sama — lapan koin kripto dan kunci kadar 30 minit.