G.SKILL
G.SKILL F3-2400C11Q-16GSR 16GB (4x4GB) DDR3 2400 CL11 desktop RAM
- 16GB (4 x 4GB)
- DDR3 2400 (PC3 1920…
$74,99
0.00097105BTC
Stokta
G.SKILL
G.SKILL F3-2400C11D-8GSR Sniper Series 8GB (2 x 4GB) DDR3 2400 CL11 desktop RAM
Dual-channel 8 GB DDR3 2400 kit with CL11 11-13-13-31 timings at 1.65 V, XMP 1.3 ready for Z77 platforms
- Capacity8GB (2 x 4GB)
- SpeedDDR3 2400 (PC3 19200)
- CAS LatencyCL11
- Timing11-13-13-31
- Voltage1.65V
- ECCNo
Capacity 8GB (2 x 4GB)
- 8GB (2 x 4GB)
- 16GB (4 x 4GB)
- Dual-channel kit doubles bandwidth for responsive multitasking
- DDR3 2400 speed delivers 19.2 GB/s per channel throughput
- CL11 11-13-13-31 timings keep latency low
- 65 V operation balances performance with stability
- Intel XMP 1.3 profile enables one-click overclocking setup
Kit Identity
The G.SKILL Sniper Series F3-2400C11D-8GSR is an 8 GB dual-channel kit built from two 4 GB DDR3 modules. It runs at 2400 MHz with timings of 11-13-13-31 and a CAS latency of 11. The kit operates at 1.65 V and includes Intel XMP 1.3 profiles tuned for 3rd Generation Intel Core processors and the Z77 platform. The black heatspreaders are designed for desktop builds that use this specific memory generation.
Fit and Limits
This kit suits enthusiasts upgrading or repairing a Z77-based system that can supply 1.65 V and supports XMP 1.3 profiles. It is not suited for platforms that require ECC or registered modules, nor for boards limited to lower voltage operation. Builders needing more than 8 GB of total capacity or a different memory generation should look at alternative products.
Deciding Spec
The 1.65 V operating voltage is the critical specification; the motherboard and CPU memory controller must be rated for this level to run the kit at its rated 2400 MHz speed and CL11 timings. If the platform cannot deliver 1.65 V, the modules will not achieve their advertised performance.
Öne çıkanlar
- Dual-channel kit doubles bandwidth for responsive multitasking
- DDR3 2400 speed delivers 19.2 GB/s per channel throughput
- CL11 11-13-13-31 timings keep latency low
- 65 V operation balances performance with stability
- Intel XMP 1.3 profile enables one-click overclocking setup
Teknik özellikler
| Brand | G.SKILL |
|---|---|
| Series | Sniper Series |
| Model | F3-2400C11D-8GSR |
| Capacity | 8GB (2 x 4GB) |
| Speed | DDR3 2400 (PC3 19200) |
| CAS Latency | CL11 |
| Timing | 11-13-13-31 |
| Voltage | 1.65V |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Multi-channel Kit | Dual Channel Kit |
| Color | Black |
| Features | Designed for 3rd Generation Intel Core Processors and Z77 platform. Intel XMP 1.3 Ready for 3rd Generation Intel Core Processors. Recommended Intel Core i7-3770K processors & Core i5-3570K processors for best performance. |
| Kargo ağırlığı | 0.12 kg |
| Koli boyutu | 204 × 137 × 20 mm |
Bu modelin diğer sürümleri
Aynı seriden 1 tane daha
Aynı aile, farklı bellek, soğutucu veya frekans — karar vermeden önce karşılaştırın.
Bu ürünle ilgili sorular
Will this kit run at 2400 MHz on a Z77 board with an i5-3570K?
The kit is rated at DDR3 2400 with CL11 11-13-13-31 timing at 1.65 V and includes an Intel XMP 1.3 profile. Enabling XMP in the BIOS will set the rated speed and timings automatically.
Does the 1.65 V rating work with standard Intel 3rd-generation memory controllers?
Intel specifies 1.5 V for 3rd-generation Core processors. The modules run at 1.65 V to reach 2400 MHz, so the memory controller will operate above its nominal voltage when XMP is enabled.
What do I need to check before installing these two 4 GB sticks?
Verify that your motherboard has two free DDR3 DIMM slots, supports dual-channel operation, and can supply 1.65 V. Then enable the XMP profile in BIOS to run at the rated 2400 MHz speed.
Bu reyondan diğerleri
Müşteriler bunları karşılaştırdı
Aynı raf, aynı sipariş tamamlama — sekiz koin ve 30 dakikalık kur kilidi.
BFKK
BFKK 3U Rackmount Server Chassis EATX/ATX/MATX 4x5.25 6x3.5 Top/Side Cooling
- Rackmount
$214,99
0.00278391BTC
Stokta
