Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Two black low-profile DDR3 modules with minimalist heatsinks

G.SKILL

G.SKILL F3-2400C11D-8GSR Sniper Series 8GB (2 x 4GB) DDR3 2400 CL11 desktop RAM

SKU CH-J8CJ-WJXJ1 MPN F3-2400C11D-8GSR

Dual-channel 8 GB DDR3 2400 kit with CL11 11-13-13-31 timings at 1.65 V, XMP 1.3 ready for Z77 platforms

  • Capacity8GB (2 x 4GB)
  • SpeedDDR3 2400 (PC3 19200)
  • CAS LatencyCL11
  • Timing11-13-13-31
  • Voltage1.65V
  • ECCNo

Capacity 8GB (2 x 4GB)

  • Dual-channel kit doubles bandwidth for responsive multitasking
  • DDR3 2400 speed delivers 19.2 GB/s per channel throughput
  • CL11 11-13-13-31 timings keep latency low
  • 65 V operation balances performance with stability
  • Intel XMP 1.3 profile enables one-click overclocking setup

Kit Identity

The G.SKILL Sniper Series F3-2400C11D-8GSR is an 8 GB dual-channel kit built from two 4 GB DDR3 modules. It runs at 2400 MHz with timings of 11-13-13-31 and a CAS latency of 11. The kit operates at 1.65 V and includes Intel XMP 1.3 profiles tuned for 3rd Generation Intel Core processors and the Z77 platform. The black heatspreaders are designed for desktop builds that use this specific memory generation.

Fit and Limits

This kit suits enthusiasts upgrading or repairing a Z77-based system that can supply 1.65 V and supports XMP 1.3 profiles. It is not suited for platforms that require ECC or registered modules, nor for boards limited to lower voltage operation. Builders needing more than 8 GB of total capacity or a different memory generation should look at alternative products.

Deciding Spec

The 1.65 V operating voltage is the critical specification; the motherboard and CPU memory controller must be rated for this level to run the kit at its rated 2400 MHz speed and CL11 timings. If the platform cannot deliver 1.65 V, the modules will not achieve their advertised performance.

Kohokohdat

  • Dual-channel kit doubles bandwidth for responsive multitasking
  • DDR3 2400 speed delivers 19.2 GB/s per channel throughput
  • CL11 11-13-13-31 timings keep latency low
  • 65 V operation balances performance with stability
  • Intel XMP 1.3 profile enables one-click overclocking setup

Tekniset tiedot

BrandG.SKILL
SeriesSniper Series
ModelF3-2400C11D-8GSR
Capacity8GB (2 x 4GB)
SpeedDDR3 2400 (PC3 19200)
CAS LatencyCL11
Timing11-13-13-31
Voltage1.65V
ECCNo
Buffered/RegisteredUnbuffered
Multi-channel KitDual Channel Kit
ColorBlack
FeaturesDesigned for 3rd Generation Intel Core Processors and Z77 platform.
Intel XMP 1.3 Ready for 3rd Generation Intel Core Processors.
Recommended Intel Core i7-3770K processors & Core i5-3570K processors for best performance.
Lähetyspaino0.12 kg
Pakkauksen mitat204 × 137 × 20 mm

Tämän mallin muut versiot

1 lisää samasta mallistosta

Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.

Kysymyksiä tästä tuotteesta

Will this kit run at 2400 MHz on a Z77 board with an i5-3570K?

The kit is rated at DDR3 2400 with CL11 11-13-13-31 timing at 1.65 V and includes an Intel XMP 1.3 profile. Enabling XMP in the BIOS will set the rated speed and timings automatically.

Does the 1.65 V rating work with standard Intel 3rd-generation memory controllers?

Intel specifies 1.5 V for 3rd-generation Core processors. The modules run at 1.65 V to reach 2400 MHz, so the memory controller will operate above its nominal voltage when XMP is enabled.

What do I need to check before installing these two 4 GB sticks?

Verify that your motherboard has two free DDR3 DIMM slots, supports dual-channel operation, and can supply 1.65 V. Then enable the XMP profile in BIOS to run at the rated 2400 MHz speed.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.