Kripto para kabul ediyoruz — böylece elinizdeki koinlerle gerçek donanım alabilirsiniz.Kripto parayla ödeyin, onu gerçek donanıma harcayın. $399 üzeri siparişlerde dünya genelinde sigortalı kargo ücretsizdir. Sade, markasız koliler Almanya’dan gönderilir.$399 üzeri siparişlerde sigortalı kargo ücretsizdir. Ödeme sayfası açıldığında kurunuz 30 dakika kilitli kalır.Kur 30 dakika kilitli. Her ürün mühürlüdür, seri numarası kontrol edilir ve 24 ay garanti kapsamındadır.Mühürlü, 24 ay garantili.

Favori ürünler Giriş yap
Compact black ABS power supply tester with 20/24-pin ATX, SATA, HDD and floppy connectors plus LED voltage indicators

myVolts

myVolts Power Supply Tester 20/24-pin ATX SATA HDD Black

SKU CH-6WXR-CW5BY

Tests 20/24-pin ATX, SATA and HDD power connectors with LED voltage indicators

  • TypeAT
  • Test 20-pin and 24-pin ATX connectors safely
  • Check +3.3 V, +5 V, +12 V rails with LED indicators
  • Verify SATA power lines (+12 V, +3.3 V, +5 V) before use
  • Detect faulty P4/P6/P8 and floppy power rails early
  • Compact ABS body fits in any toolkit

Compact ATX power supply tester

The myVolts tester checks 20-pin and 24-pin ATX connectors plus SATA, floppy and 4, 6 and 8-pin HDD power plugs. It is built for technicians and hobbyists who need a quick go/no-go verdict before installing a unit. A row of LEDs shows the status of each rail at a glance. No software or external power is required.

Rugged ABS body with direct plug-in sockets

The black ABS housing measures roughly 2.76 by 1.97 by 0.79 inches and fits in a tool bag. Every connector faces the same side so you can plug a supply in without hunting for orientation. The sockets accept standard ATX, SATA, floppy and peripheral power plugs directly, no adapters needed. It is a passive device that draws its test current from the supply under test.

Instant rail verification with LED indicators

Seven LEDs on the right report +3.3 V, -12 V, PG, +5 VSB, +12 V, -5 V and +5 V on the main connector. Separate left-hand LEDs cover +12 V and +5 V for HDD, +12 V for P4/P6/P8, +12 V and +5 V for floppy, and +12 V, +3.3 V and +5 V for SATA. All lights lit means the rail is present; a missing light flags a fault immediately. Not suited for builders who need load testing or ripple measurement.

Öne çıkanlar

  • Test 20-pin and 24-pin ATX connectors safely
  • Check +3.3 V, +5 V, +12 V rails with LED indicators
  • Verify SATA power lines (+12 V, +3.3 V, +5 V) before use
  • Detect faulty P4/P6/P8 and floppy power rails early
  • Compact ABS body fits in any toolkit

Teknik özellikler

TypeAT

Bu ürünle ilgili sorular

Does the 20/24-pin ATX connector test the PG signal and all seven voltage rails?

Yes, the 20/24-pin socket checks +3.3V, -12V, PG, +5VSB, +12V, -5V and +5V; all seven LEDs must light for a healthy supply.

What are the exact dimensions of the tester so I know it fits my tool drawer?

The rugged ABS body measures approximately 2.76 by 1.97 by 0.79 inches (7 by 5 by 2 cm).

In what order do I connect the different power leads to avoid missing a rail?

Test the 24-pin first, then HDD (+12V/+5V), then P4/P6/P8 (+12V), then floppy (+12V/+5V), and finally SATA (+12V/+3.3V/+5V).

Bu reyondan diğerleri

Müşteriler bunları karşılaştırdı

Aynı raf, aynı sipariş tamamlama — sekiz koin ve 30 dakikalık kur kilidi.