Wij accepteren cryptovaluta — zo kunnen de munten die u bezit echte hardware kopen.Betaal in crypto, besteed het aan echte hardware. Gratis verzekerde verzending wereldwijd vanaf $399. Neutrale dozen zonder merk, verzonden vanuit Duitsland.Gratis verzekerde verzending vanaf $399. Uw koers wordt 30 minuten vastgezet zodra het afrekenen begint.Koers 30 minuten vastgezet. Elk artikel is verzegeld, het serienummer wordt gecontroleerd, en het valt onder 24 maanden garantie.Verzegeld, 24 maanden garantie.

Favoriete artikelen Inloggen
Compact black ABS power supply tester with 20/24-pin ATX, SATA, HDD and floppy connectors plus LED voltage indicators

myVolts

myVolts Power Supply Tester 20/24-pin ATX SATA HDD Black

SKU CH-6WXR-CW5BY

Tests 20/24-pin ATX, SATA and HDD power connectors with LED voltage indicators

  • TypeAT
  • Test 20-pin and 24-pin ATX connectors safely
  • Check +3.3 V, +5 V, +12 V rails with LED indicators
  • Verify SATA power lines (+12 V, +3.3 V, +5 V) before use
  • Detect faulty P4/P6/P8 and floppy power rails early
  • Compact ABS body fits in any toolkit

Compact ATX power supply tester

The myVolts tester checks 20-pin and 24-pin ATX connectors plus SATA, floppy and 4, 6 and 8-pin HDD power plugs. It is built for technicians and hobbyists who need a quick go/no-go verdict before installing a unit. A row of LEDs shows the status of each rail at a glance. No software or external power is required.

Rugged ABS body with direct plug-in sockets

The black ABS housing measures roughly 2.76 by 1.97 by 0.79 inches and fits in a tool bag. Every connector faces the same side so you can plug a supply in without hunting for orientation. The sockets accept standard ATX, SATA, floppy and peripheral power plugs directly, no adapters needed. It is a passive device that draws its test current from the supply under test.

Instant rail verification with LED indicators

Seven LEDs on the right report +3.3 V, -12 V, PG, +5 VSB, +12 V, -5 V and +5 V on the main connector. Separate left-hand LEDs cover +12 V and +5 V for HDD, +12 V for P4/P6/P8, +12 V and +5 V for floppy, and +12 V, +3.3 V and +5 V for SATA. All lights lit means the rail is present; a missing light flags a fault immediately. Not suited for builders who need load testing or ripple measurement.

Pluspunten

  • Test 20-pin and 24-pin ATX connectors safely
  • Check +3.3 V, +5 V, +12 V rails with LED indicators
  • Verify SATA power lines (+12 V, +3.3 V, +5 V) before use
  • Detect faulty P4/P6/P8 and floppy power rails early
  • Compact ABS body fits in any toolkit

Specificaties

TypeAT

Vragen over dit artikel

Does the 20/24-pin ATX connector test the PG signal and all seven voltage rails?

Yes, the 20/24-pin socket checks +3.3V, -12V, PG, +5VSB, +12V, -5V and +5V; all seven LEDs must light for a healthy supply.

What are the exact dimensions of the tester so I know it fits my tool drawer?

The rugged ABS body measures approximately 2.76 by 1.97 by 0.79 inches (7 by 5 by 2 cm).

In what order do I connect the different power leads to avoid missing a rail?

Test the 24-pin first, then HDD (+12V/+5V), then P4/P6/P8 (+12V), then floppy (+12V/+5V), and finally SATA (+12V/+3.3V/+5V).

Ook in deze afdeling

Klanten vergeleken ook

Dezelfde afdeling, dezelfde kassa — acht munten en een koers die 30 minuten vaststaat.