BFKK
BFKK 3U Rackmount Server Chassis EATX/ATX/MATX 4x5.25 6x3.5 Top/Side Cooling
- Rackmount
$214,99
0.00278448BTC
Stokta
NEMIX RAM
NEMIX RAM 8GB (2x4GB) DDR3 1333 PC3-10600 1.35V 204-Pin SODIMM Kit for POSIFLEX XT-5517 JIVA 17 memory upgrade
An 8 GB DDR3 kit (two 4 GB SODIMMs) running at 1333 MHz with CL9 latency, 1.35 V operation and 204-pin layout, validated for the POSIFLEX XT-5517 JIVA 17 terminal
- Capacity8GB (2 x 4GB)
- SpeedDDR3 1333 (PC3 10600)
- ECCNo
- Buffered/RegisteredUnbuffered
- ChipsetMajor OEM Samsung, Micron, Hynix
- Voltage1.50V
- 8 GB kit expands POS terminal memory
- DDR3 1333 speed matches system requirements
- 35 V low-voltage modules reduce power draw
- 204-pin SODIMM form factor fits the XT-5517
- CL9 latency supports responsive transaction processing
POSIFLEX XT-5517 JIVA 17 kit
This 8GB kit contains two 4GB DDR3 SODIMM modules built for the POSIFLEX XT-5517 JIVA 17 terminal. Each stick runs at 1333 MT/s with CL9 latency and operates at 1.35 V. The 204-pin form factor matches the slot layout used in this point-of-sale system.
Replaces factory 4GB or 2GB configs
Upgrading from a single 4GB module or a pair of 2GB modules adds headroom for multi-tasking POS software and background services. The jump is worth it when the terminal runs several applications at once or handles larger local databases without swapping to slower storage.
Fits the terminal's two SODIMM slots
The kit fills both slots for dual-channel operation and requires no heat spreader clearance. Non-ECC unbuffered design matches the board's memory controller, and 1.35 V low-voltage parts keep power draw within the original spec. No extra cables or brackets are needed.
Öne çıkanlar
- 8 GB kit expands POS terminal memory
- DDR3 1333 speed matches system requirements
- 35 V low-voltage modules reduce power draw
- 204-pin SODIMM form factor fits the XT-5517
- CL9 latency supports responsive transaction processing
Teknik özellikler
| Brand | NEMIX RAM |
|---|---|
| Series | POSIFLEX POS Series Point of Sale Kiosk Memory |
| Model | POSIFLEX POS DDR3 1333MHZ Non-ECC Unbuffered SODIMM |
| Part Number | MS10600-428K2 |
| Capacity | 8GB (2 x 4GB) |
| Speed | DDR3 1333 (PC3 10600) |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Chipset | Major OEM Samsung, Micron, Hynix |
| Voltage | 1.50V |
| Compatible System | POSIFLEX POS |
| CAS Latency | CL9 |
| Heat Spreader | No |
| Type | 204-Pin DDR3 SODIMM |
| Rank | 2Rx8 |
| Features | DDR3 Non-ECC Unbuffered SODIMM Motherboard Compatible |
| Package Content | 8GB (2X4GB) DDR3 1333MHZ PC3-10600 2Rx8 1.35V 204-PIN Non-ECC Unbuffered SODIMM KIT |
Bu ürünle ilgili sorular
Does this 204-pin DDR3 SODIMM kit fit the POSIFLEX XT-5517 JIVA 17 terminal?
Yes, the kit is built specifically for the POSIFLEX XT-5517 JIVA 17 and uses the 204-pin DDR3 SODIMM form factor required by that terminal.
What is the correct way to install the two 4 GB modules, and what step is often missed?
Power off the terminal, open the memory compartment, insert each module at an angle until the gold contacts are fully seated, then press down until both side clips click; the step often missed is pressing firmly enough to engage both clips on each module.
Will these modules need any firmware updates or periodic replacement after installation?
No firmware updates are required; the modules are tested for stability and carry a lifetime replacement warranty, so they only need replacement if a hardware fault occurs.
Bu reyondan diğerleri
Müşteriler bunları karşılaştırdı
Aynı raf, aynı sipariş tamamlama — sekiz koin ve 30 dakikalık kur kilidi.
