Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Two green 204-pin DDR3 SODIMM modules in anti-static bag

NEMIX RAM

NEMIX RAM 8GB (2x4GB) DDR3 1333 PC3-10600 1.35V 204-Pin SODIMM Kit for POSIFLEX XT-5517 JIVA 17 memory upgrade

SKU CH-TN1X-49C9V

An 8 GB DDR3 kit (two 4 GB SODIMMs) running at 1333 MHz with CL9 latency, 1.35 V operation and 204-pin layout, validated for the POSIFLEX XT-5517 JIVA 17 terminal

  • Capacity8GB (2 x 4GB)
  • SpeedDDR3 1333 (PC3 10600)
  • ECCNo
  • Buffered/RegisteredUnbuffered
  • ChipsetMajor OEM Samsung, Micron, Hynix
  • Voltage1.50V
  • 8 GB kit expands POS terminal memory
  • DDR3 1333 speed matches system requirements
  • 35 V low-voltage modules reduce power draw
  • 204-pin SODIMM form factor fits the XT-5517
  • CL9 latency supports responsive transaction processing

POSIFLEX XT-5517 JIVA 17 kit

This 8GB kit contains two 4GB DDR3 SODIMM modules built for the POSIFLEX XT-5517 JIVA 17 terminal. Each stick runs at 1333 MT/s with CL9 latency and operates at 1.35 V. The 204-pin form factor matches the slot layout used in this point-of-sale system.

Replaces factory 4GB or 2GB configs

Upgrading from a single 4GB module or a pair of 2GB modules adds headroom for multi-tasking POS software and background services. The jump is worth it when the terminal runs several applications at once or handles larger local databases without swapping to slower storage.

Fits the terminal's two SODIMM slots

The kit fills both slots for dual-channel operation and requires no heat spreader clearance. Non-ECC unbuffered design matches the board's memory controller, and 1.35 V low-voltage parts keep power draw within the original spec. No extra cables or brackets are needed.

Helstu kostir

  • 8 GB kit expands POS terminal memory
  • DDR3 1333 speed matches system requirements
  • 35 V low-voltage modules reduce power draw
  • 204-pin SODIMM form factor fits the XT-5517
  • CL9 latency supports responsive transaction processing

Tæknilýsing

BrandNEMIX RAM
SeriesPOSIFLEX POS Series Point of Sale Kiosk Memory
ModelPOSIFLEX POS DDR3 1333MHZ Non-ECC Unbuffered SODIMM
Part NumberMS10600-428K2
Capacity8GB (2 x 4GB)
SpeedDDR3 1333 (PC3 10600)
ECCNo
Buffered/RegisteredUnbuffered
ChipsetMajor OEM Samsung, Micron, Hynix
Voltage1.50V
Compatible SystemPOSIFLEX POS
CAS LatencyCL9
Heat SpreaderNo
Type204-Pin DDR3 SODIMM
Rank2Rx8
FeaturesDDR3 Non-ECC Unbuffered SODIMM Motherboard Compatible
Package Content8GB (2X4GB) DDR3 1333MHZ PC3-10600 2Rx8 1.35V 204-PIN Non-ECC Unbuffered SODIMM KIT

Spurningar um þessa vöru

Does this 204-pin DDR3 SODIMM kit fit the POSIFLEX XT-5517 JIVA 17 terminal?

Yes, the kit is built specifically for the POSIFLEX XT-5517 JIVA 17 and uses the 204-pin DDR3 SODIMM form factor required by that terminal.

What is the correct way to install the two 4 GB modules, and what step is often missed?

Power off the terminal, open the memory compartment, insert each module at an angle until the gold contacts are fully seated, then press down until both side clips click; the step often missed is pressing firmly enough to engage both clips on each module.

Will these modules need any firmware updates or periodic replacement after installation?

No firmware updates are required; the modules are tested for stability and carry a lifetime replacement warranty, so they only need replacement if a hardware fault occurs.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.