Kripto para kabul ediyoruz — böylece elinizdeki koinlerle gerçek donanım alabilirsiniz.Kripto parayla ödeyin, onu gerçek donanıma harcayın. $399 üzeri siparişlerde dünya genelinde sigortalı kargo ücretsizdir. Sade, markasız koliler Almanya’dan gönderilir.$399 üzeri siparişlerde sigortalı kargo ücretsizdir. Ödeme sayfası açıldığında kurunuz 30 dakika kilitli kalır.Kur 30 dakika kilitli. Her ürün mühürlüdür, seri numarası kontrol edilir ve 24 ay garanti kapsamındadır.Mühürlü, 24 ay garantili.

Favori ürünler Giriş yap
Small black 40mm axial fan with three-pin connector

OEM Industries

OEM Industries IXP-11-DVI 4010 6000RPM CPU cooler

SKU CH-6XKC-6Y5C7

A 40 mm ball-bearing fan spinning up to 6499 rpm for tight-case or switch cooling

  • ColorBlack
  • TypeFan only
  • Fan Size40mm
  • Bearing TypeBall
  • Power Connector3 Pin
  • LEDNo
  • High 6000 RPM airflow for tight spaces
  • Ball bearing design extends operational life
  • 40×10 mm micro form fits small cases
  • 3-pin 12 V connector enables simple install
  • No LED keeps builds clean and distraction-free

Micro axial cooler for tight spaces

The OEM Industries IXP-11-DVI is a 40 mm ball-bearing fan designed as a micro axial cooler for CPUs, switches or other compact hardware. It runs at 6000 to 6499 rpm on a 12 V three-pin connector and has no LED lighting. The black 4010 frame fits a 40 mm mounting pattern.

For builders who need a 40 mm replacement fan

This cooler suits anyone replacing a 40 mm unit in a small-form-factor case, a network switch or an embedded board where a larger fan cannot be installed. It is not for builders who need more airflow than a 40 mm frame can deliver or who require PWM speed control.

40 mm mounting pattern decides fit

The only specification that determines compatibility is the 40 mm square mounting hole spacing. If the target device uses a different hole pattern or a larger fan cut-out, this cooler will not attach.

Öne çıkanlar

  • High 6000 RPM airflow for tight spaces
  • Ball bearing design extends operational life
  • 40×10 mm micro form fits small cases
  • 3-pin 12 V connector enables simple install
  • No LED keeps builds clean and distraction-free

Teknik özellikler

ModelIXP-11-DVI
ColorBlack
TypeFan only
Fan Size40mm
Bearing TypeBall
Power Connector3 Pin
LEDNo

Bu ürünle ilgili sorular

Will the 40mm fan fit a standard 40x10mm mounting pattern?

The fan measures 40mm square by 10mm thick, matching the common 40x10mm screw spacing used on many small-form-factor boards and switch chassis.

How do I connect the 3-pin power connector without reversing polarity?

Align the keyed notch on the 3-pin plug with the tab on the motherboard or controller header; the yellow wire is 12V, black is ground, and the third wire carries the tachometer signal.

When should I plan to replace the ball-bearing fan?

Ball bearings typically run for tens of thousands of hours at 6000-6499 RPM; listen for new whine or vibration and swap the unit when noise becomes noticeable.

Bu reyondan diğerleri

Müşteriler bunları karşılaştırdı

Aynı raf, aynı sipariş tamamlama — sekiz koin ve 30 dakikalık kur kilidi.