Kripto para kabul ediyoruz — böylece elinizdeki koinlerle gerçek donanım alabilirsiniz.Kripto parayla ödeyin, onu gerçek donanıma harcayın. $399 üzeri siparişlerde dünya genelinde sigortalı kargo ücretsizdir. Sade, markasız koliler Almanya’dan gönderilir.$399 üzeri siparişlerde sigortalı kargo ücretsizdir. Ödeme sayfası açıldığında kurunuz 30 dakika kilitli kalır.Kur 30 dakika kilitli. Her ürün mühürlüdür, seri numarası kontrol edilir ve 24 ay garanti kapsamındadır.Mühürlü, 24 ay garantili.

Favori ürünler Giriş yap
Solidigm D7-PS1010 E1.S 9.5mm enterprise SSD, bare circuit board with edge connector, green PCB and silver label

Solidigm

Solidigm D7-PS1010 SB5PHU7X038T001 enterprise SSD 3.84TB E1.S 9.5mm PCIe 5.0 x4 TLC

SKU CH-T6FD-0HC85 MPN SB5PHU7X038T001

E1.S 9.5mm enterprise SSD delivering 3.84TB of TLC storage over a PCIe 5.0 x4 interface

  • Form FactorE1.S 9.5mm
  • Capacity3.84TB
  • Memory ComponentsTLC
  • InterfacePCI-Express 5.0 x4
  • SecurityNo Opal

Option 3.84TB E1.S 9.5mm

20 yapılandırma daha gösterin
  • E1.S 9.5mm form factor fits dense server chassis
  • PCIe 5.0 x4 interface delivers high-throughput data paths
  • 84TB capacity stores large enterprise datasets
  • TLC memory components balance endurance and capacity
  • No Opal security simplifies deployment in managed environments

3.84TB E1.S enterprise drive

The Solidigm D7-PS1010 is a 3.84TB enterprise SSD built in the E1.S 9.5mm form factor. It connects through a PCI-Express 5.0 x4 interface and uses TLC memory components. The drive ships without Opal security features. It is designed for internal server and data-centre deployments.

Suits high-density server bays

This drive suits administrators who need a 3.84TB capacity in the compact E1.S 9.5mm size for modern server chassis. It is not for systems that only accept 2.5-inch U.2 or U.3 drives, nor for platforms limited to PCIe 4.0 or earlier interfaces. Buyers who require hardware-based encryption should look at Opal-enabled models instead.

Verify E1.S slot and PCIe 5.0 support

Before ordering, confirm that the target server has an E1.S 9.5mm drive bay and a backplane or riser wired for PCI-Express 5.0 x4 operation. Check the system firmware for compatibility with Solidigm D7-PS1010 drives. Ensure the platform can supply adequate cooling for the 9.5mm module under sustained workloads.

Öne çıkanlar

  • E1.S 9.5mm form factor fits dense server chassis
  • PCIe 5.0 x4 interface delivers high-throughput data paths
  • 84TB capacity stores large enterprise datasets
  • TLC memory components balance endurance and capacity
  • No Opal security simplifies deployment in managed environments

Teknik özellikler

BrandSolidigm
ModelD7-PS1010
Part NumberSB5PHU7X038T001
Form FactorE1.S 9.5mm
Capacity3.84TB
Memory ComponentsTLC
InterfacePCI-Express 5.0 x4
SecurityNo Opal
Kargo ağırlığı0.12 kg
Koli boyutu140 × 110 × 16 mm

Bu modelin diğer sürümleri

Aynı seriden 5 tane daha

Aynı aile, farklı bellek, soğutucu veya frekans — karar vermeden önce karşılaştırın.

Bu ürünle ilgili sorular

Does my server need an E1.S 9.5mm drive bay and a PCIe 5.0 x4 slot to install this 3.84TB SSD?

Yes, the drive fits an E1.S 9.5mm bay and connects through a PCIe 5.0 x4 interface, so both must be present in the chassis.

Will this PCIe 5.0 x4 drive still operate if I keep my older PCIe 4.0 backplane?

The SSD is backward compatible and will run at PCIe 4.0 speeds when installed in a PCIe 4.0 backplane.

How can I verify the 3.84TB TLC drive is healthy after installation?

Check the drive appears at full capacity in the BIOS or OS, then run a SMART health report to confirm no errors.

Bu reyondan diğerleri

Müşteriler bunları karşılaştırdı

Aynı raf, aynı sipariş tamamlama — sekiz koin ve 30 dakikalık kur kilidi.