Sprejemamo kriptovalute — tako lahko sredstva, ki jih imate, kupijo pravo strojno opremo.Plačajte v kriptovaluti, zapravite jo za pravo strojno opremo. Brezplačna zavarovana dostava po vsem svetu nad 399 $. Nevtralni kartoni brez znamke, poslani iz Nemčije.Brezplačna zavarovana dostava nad 399 $. Vaš tečaj je zaklenjen za 30 minut, takoj ko se odpre blagajna.Tečaj zaklenjen 30 minut. Vsak izdelek je zapečaten, njegova serijska številka preverjena, in krit z 24-mesečno garancijo.Zapečateno, 24-mesečna garancija.

Spremljani izdelki Prijava
Solidigm D7-PS1010 E1.S 9.5mm enterprise SSD, bare circuit board with edge connector, green PCB and silver label

Solidigm

Solidigm D7-PS1010 SB5PHU7X038T001 enterprise SSD 3.84TB E1.S 9.5mm PCIe 5.0 x4 TLC

SKU CH-T6FD-0HC85 MPN SB5PHU7X038T001

E1.S 9.5mm enterprise SSD delivering 3.84TB of TLC storage over a PCIe 5.0 x4 interface

  • Form FactorE1.S 9.5mm
  • Capacity3.84TB
  • Memory ComponentsTLC
  • InterfacePCI-Express 5.0 x4
  • SecurityNo Opal

Option 3.84TB E1.S 9.5mm

Prikaži še 20 konfiguracij
  • E1.S 9.5mm form factor fits dense server chassis
  • PCIe 5.0 x4 interface delivers high-throughput data paths
  • 84TB capacity stores large enterprise datasets
  • TLC memory components balance endurance and capacity
  • No Opal security simplifies deployment in managed environments

3.84TB E1.S enterprise drive

The Solidigm D7-PS1010 is a 3.84TB enterprise SSD built in the E1.S 9.5mm form factor. It connects through a PCI-Express 5.0 x4 interface and uses TLC memory components. The drive ships without Opal security features. It is designed for internal server and data-centre deployments.

Suits high-density server bays

This drive suits administrators who need a 3.84TB capacity in the compact E1.S 9.5mm size for modern server chassis. It is not for systems that only accept 2.5-inch U.2 or U.3 drives, nor for platforms limited to PCIe 4.0 or earlier interfaces. Buyers who require hardware-based encryption should look at Opal-enabled models instead.

Verify E1.S slot and PCIe 5.0 support

Before ordering, confirm that the target server has an E1.S 9.5mm drive bay and a backplane or riser wired for PCI-Express 5.0 x4 operation. Check the system firmware for compatibility with Solidigm D7-PS1010 drives. Ensure the platform can supply adequate cooling for the 9.5mm module under sustained workloads.

Poudarki

  • E1.S 9.5mm form factor fits dense server chassis
  • PCIe 5.0 x4 interface delivers high-throughput data paths
  • 84TB capacity stores large enterprise datasets
  • TLC memory components balance endurance and capacity
  • No Opal security simplifies deployment in managed environments

Specifikacije

BrandSolidigm
ModelD7-PS1010
Part NumberSB5PHU7X038T001
Form FactorE1.S 9.5mm
Capacity3.84TB
Memory ComponentsTLC
InterfacePCI-Express 5.0 x4
SecurityNo Opal
Teža pošiljke0.12 kg
Velikost pošiljke140 × 110 × 16 mm

Druge različice tega modela

še 5 v isti paleti

Ista družina, različen pomnilnik, hladilnik ali takt — primerjajte, preden se odločite.

Vprašanja o tem izdelku

Does my server need an E1.S 9.5mm drive bay and a PCIe 5.0 x4 slot to install this 3.84TB SSD?

Yes, the drive fits an E1.S 9.5mm bay and connects through a PCIe 5.0 x4 interface, so both must be present in the chassis.

Will this PCIe 5.0 x4 drive still operate if I keep my older PCIe 4.0 backplane?

The SSD is backward compatible and will run at PCIe 4.0 speeds when installed in a PCIe 4.0 backplane.

How can I verify the 3.84TB TLC drive is healthy after installation?

Check the drive appears at full capacity in the BIOS or OS, then run a SMART health report to confirm no errors.

Tudi v tem oddelku

Stranke so primerjale tudi te

Ista polica, ista blagajna — osem kriptovalut in 30-minutni zaklep tečaja.