NEMIX RAM DDR5-5600 2TB (16x128GB) ECC RDIMM CL46 1.1V Supermicro H14SST-G memory upgrade
- 2TB (16 x 128GB)
- 288-Pin DDR5 RDIMM
Приемаме криптовалута — така монетите, които притежавате, могат да купят истински хардуер.Платете с крипто, похарчете го за истински хардуер. Безплатна застрахована доставка по целия свят над 399 $. Неутрални кашони без марка, изпратени от Германия.Безплатна застрахована доставка над 399 $. Курсът Ви е заключен за 30 минути веднага след отварянето на касата.Курс, заключен за 30 минути. Всеки артикул е запечатан, серийният му номер е проверен, и е покрит с 24-месечна гаранция.Запечатан, 24-месечна гаранция.
A-Tech
8GB DDR3 1066MHz ECC registered server memory module with 2Rx4 organisation and 1.5V operation
This 8GB DDR3 1066 (PC3-8500) module is a registered ECC DIMM built for HP server and workstation platforms. It replaces HP part numbers 500206-071, 500664-B21, 516423-B21, 516423-S21 and 519201-001. The 240-pin form factor fits DDR3 slots in compatible systems. It targets administrators upgrading memory capacity in supported HP hardware.
Registered buffering and ECC correction maintain data integrity during continuous server operations. The module operates at standard 1.5V DDR3 voltage with CL7 latency. Major-brand chips are tested for dependable performance under load. It is not suited for desktop boards that require unbuffered non-ECC memory or for systems limited to lower-density modules.
The dual-rank 2Rx4 configuration determines compatibility with specific HP memory controllers and maximum population rules. Verify your system's qualified vendor list before purchase. This module will not work in platforms that only accept single-rank or unbuffered DIMMs.
| Brand | A-Tech |
|---|---|
| Capacity | 8GB |
| Speed | DDR3 1066 (PC3 8500) |
| CAS Latency | CL7 |
| Voltage | 1.50V |
| ECC | Yes |
| Buffered/Registered | Registered |
| Rank | 2Rx4 |
| Chipset | Major Brand Chipset |
| Features | Major Brand Chips |
The module operates at the standard DDR3 voltage of 1.50V and a speed of 1066 MHz; registered ECC DIMMs of this type typically run cool under sustained load because the register buffers the address and command signals, reducing electrical stress on the memory controller.
Your board needs a 240-pin DDR3 DIMM slot that supports registered ECC memory at 1066 MHz (PC3-8500) with a 1.5V supply and a chipset or BIOS that enables the register and ECC functions.
Mixing ranks or capacities is often possible on servers that support flexible population rules, but the system will run all modules at the speed and timings of the slowest installed DIMM; check your server's memory configuration guide for approved combinations.
Още от този рафт
Същият рафт, същата каса — осем монети и заключване на курса за 30 минути.
Това, което изпращате, и това, в което четете цените.
Изпратено от Вашия портфейл при поръчката
Само за визуализация — каталогът е в долари
Никоя валута не съответства.
Изберете езика, на който сайтът да Ви говори.
Нови сте тук?
Вече имате профил?
Няма автоматично нулиране: този магазин не изпраща имейли, така че няма еднократна връзка, която да поискате. Оставете адреса в профила си и той ще бъде обработен ръчно.
Заявката е приета
Нищо няма да пристигне във Вашата пощенска кутия — този магазин изобщо не изпраща имейли. Заявките се обработват ръчно.
Спомнихте си я?