Green rectangular circuit board with black memory chips and gold edge connectors

NEMIX RAM

NEMIX RAM 16GB DDR4 2933MHz CL21 1Rx8 UDIMM memory upgrade

SKU CH-72ST-5BS8A

16GB DDR4 2933MHz CL21 UDIMM built with major OEM chips for verified Supermicro X12SCZ-F and X12SCZ-TLN4F motherboard compatibility

Capacity16GB
Type288-Pin DDR4 UDIMM
SpeedDDR4 2933 (PC4 23400)
CAS LatencyCL21
Voltage1.20V
ECCNo

Exact-match upgrade for Supermicro X12SCZ-F / X12SCZ-TLN4F motherboards
16 GB DDR4 2933 MHz CL21 runs at rated speed and voltage
1Rx8 Non-ECC UDIMM fits desktop memory controller without ECC conflicts
Major OEM chips from Samsung, Micron or Hynix tested for stability
288-pin 1.2 V unbuffered module installs in standard desktop DIMM slots

107,99 $

0.00137542 BTC με τη σημερινή ισοτιμία

Διαθέσιμο · αποστολή σήμερα

Το ταμείο κλειδώνει την ισοτιμία σας για 30 λεπτά.

Παράδοση προς Ηνωμένες Πολιτείες εκτίμηση

UPS Worldwide Expedited 3–6 εργάσιμες ημέρες 39,90 $
DHL Express Worldwide 2–3 εργάσιμες ημέρες 74,90 $

Προσθέστε 291,01 $ ακόμη και η βασική αποστολή γίνεται δωρεάν.

Οι εισαγωγικοί δασμοί επιβάλλονται κατά την άφιξη από τη χώρα σας.

Αποστολή αλλού

Exact-match DDR4 upgrade

This 16GB DDR4-2933 (PC4-23400) module is built for desktop systems that require a single-rank 1Rx8 Non-ECC UDIMM at 1.2V. It uses the precise timing and voltage the memory controller expects so the full capacity is recognised at the rated speed.

Replaces slower or smaller DIMMs

Upgrading from lower-capacity or slower DDR4 sticks is worthwhile when the motherboard supports DDR4-2933 and the existing configuration leaves free 288-pin slots. The jump adds bandwidth and capacity without changing voltage or form factor.

Check motherboard manual first

Verify that the Supermicro X12SCZ-F or X12SCZ-TLN4F board accepts 16GB Non-ECC UDIMMs in the planned slot order and that the BIOS is current enough to initialise the modules at CL21. Confirm the system does not require ECC or registered memory before ordering.

Βασικά χαρακτηριστικά

Exact-match upgrade for Supermicro X12SCZ-F / X12SCZ-TLN4F motherboards
16 GB DDR4 2933 MHz CL21 runs at rated speed and voltage
1Rx8 Non-ECC UDIMM fits desktop memory controller without ECC conflicts
Major OEM chips from Samsung, Micron or Hynix tested for stability
288-pin 1.2 V unbuffered module installs in standard desktop DIMM slots

Προδιαγραφές

Brand	NEMIX RAM
Series	NEMIX RAM Original Series Memory
Model	DDR4 Non-ECC Unbuffered UDIMM Memory
Part Number	MD23400-618K1
Capacity	16GB
Type	288-Pin DDR4 UDIMM
Speed	DDR4 2933 (PC4 23400)
CAS Latency	CL21
Voltage	1.20V
ECC	No
Buffered/Registered	Unbuffered
Rank	1Rx8
Chipset	Major OEM Samsung, Micron, Hynix
Heat Spreader	No
Compatible System	Supermicro
Features	DDR4 Non-ECC Unbuffered UDIMM Motherboard Compatible
Package Content	16GB DDR4 2933MHz PC4-23400 1Rx8 1.2V 288-PIN Non-ECC UDIMM KIT

Ερωτήσεις για αυτό το προϊόν

Will this 288-pin DDR4 UDIMM fit the memory slots on my Supermicro X12SCZ-F motherboard?

Yes, the module is a 288-pin DDR4 UDIMM, which is the exact form factor required by the Supermicro X12SCZ-F and X12SCZ-TLN4F motherboards.

What is the correct way to install this 1Rx8 UDIMM, and what step do people often miss?

Align the notch on the module with the slot key, press down firmly until both side clips click shut, then consult your motherboard manual for the approved DIMM population order.

Does this non-ECC DDR4 module need any firmware updates or component replacements over its lifetime?

No, the memory has no firmware and no moving parts; it is a passive component that does not require updates or scheduled replacements.

Επίσης σε αυτό το ράφι