Vi tar imot kryptovaluta — slik kan kryptovalutaene du eier, kjøpe ekte maskinvare.Betal med krypto, bruk den på ekte maskinvare. Gratis, forsikret levering verden over for bestillinger over 399 $. Nøytrale kartonger uten merking, sendt fra Tyskland.Gratis, forsikret levering over 399 $. Kursen din er låst i 30 minutter når kassen åpnes.Kurs låst i 30 minutter. Alle varer er forseglet, serienummerkontrollert og dekket av 24 måneders garanti.Forseglet, 24 måneders garanti.

Overvåkingsliste Logg inn
Green rectangular circuit board with black memory chips and gold edge connectors

NEMIX RAM

NEMIX RAM 16GB DDR4 2933MHz CL21 1Rx8 UDIMM memory upgrade

SKU CH-72ST-5BS8A

16GB DDR4 2933MHz CL21 UDIMM built with major OEM chips for verified Supermicro X12SCZ-F and X12SCZ-TLN4F motherboard compatibility

  • Capacity16GB
  • Type288-Pin DDR4 UDIMM
  • SpeedDDR4 2933 (PC4 23400)
  • CAS LatencyCL21
  • Voltage1.20V
  • ECCNo
  • Exact-match upgrade for Supermicro X12SCZ-F / X12SCZ-TLN4F motherboards
  • 16 GB DDR4 2933 MHz CL21 runs at rated speed and voltage
  • 1Rx8 Non-ECC UDIMM fits desktop memory controller without ECC conflicts
  • Major OEM chips from Samsung, Micron or Hynix tested for stability
  • 288-pin 1.2 V unbuffered module installs in standard desktop DIMM slots

Exact-match DDR4 upgrade

This 16GB DDR4-2933 (PC4-23400) module is built for desktop systems that require a single-rank 1Rx8 Non-ECC UDIMM at 1.2V. It uses the precise timing and voltage the memory controller expects so the full capacity is recognised at the rated speed.

Replaces slower or smaller DIMMs

Upgrading from lower-capacity or slower DDR4 sticks is worthwhile when the motherboard supports DDR4-2933 and the existing configuration leaves free 288-pin slots. The jump adds bandwidth and capacity without changing voltage or form factor.

Check motherboard manual first

Verify that the Supermicro X12SCZ-F or X12SCZ-TLN4F board accepts 16GB Non-ECC UDIMMs in the planned slot order and that the BIOS is current enough to initialise the modules at CL21. Confirm the system does not require ECC or registered memory before ordering.

Høydepunkter

  • Exact-match upgrade for Supermicro X12SCZ-F / X12SCZ-TLN4F motherboards
  • 16 GB DDR4 2933 MHz CL21 runs at rated speed and voltage
  • 1Rx8 Non-ECC UDIMM fits desktop memory controller without ECC conflicts
  • Major OEM chips from Samsung, Micron or Hynix tested for stability
  • 288-pin 1.2 V unbuffered module installs in standard desktop DIMM slots

Spesifikasjoner

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Memory
ModelDDR4 Non-ECC Unbuffered UDIMM Memory
Part NumberMD23400-618K1
Capacity16GB
Type288-Pin DDR4 UDIMM
SpeedDDR4 2933 (PC4 23400)
CAS LatencyCL21
Voltage1.20V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR4 Non-ECC Unbuffered UDIMM Motherboard Compatible
Package Content16GB DDR4 2933MHz PC4-23400 1Rx8 1.2V 288-PIN Non-ECC UDIMM KIT

Spørsmål om denne varen

Will this 288-pin DDR4 UDIMM fit the memory slots on my Supermicro X12SCZ-F motherboard?

Yes, the module is a 288-pin DDR4 UDIMM, which is the exact form factor required by the Supermicro X12SCZ-F and X12SCZ-TLN4F motherboards.

What is the correct way to install this 1Rx8 UDIMM, and what step do people often miss?

Align the notch on the module with the slot key, press down firmly until both side clips click shut, then consult your motherboard manual for the approved DIMM population order.

Does this non-ECC DDR4 module need any firmware updates or component replacements over its lifetime?

No, the memory has no firmware and no moving parts; it is a passive component that does not require updates or scheduled replacements.

Også i denne avdelingen

Kunder sammenlignet disse

Samme hylle, samme kasse — åtte mynter og 30 minutters kurslås.