Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Green rectangular circuit board with 2.1mm power jack and pin headers

Adafruit

Adafruit RGB Matrix FeatherWing Kit engineering development tool

SKU CH-DBFE-2BMFM

A FeatherWing kit that connects 16x32, 32x32 or 64x32 RGB matrices to M0 or M4 Feathers, with a 2.1mm DC jack for 5V power and two assembly options

  • TypePrototyping Products
  • Compatible with 16, 32 or 64 pixel wide RGB matrices
  • Includes 2.1mm DC jack for 5V power supply
  • Works with M0 and M4 based Feather boards
  • Two assembly options for flexible stacking configurations
  • Enables quick project creation with 16 or 32 pixel tall displays

Adafruit RGB Matrix FeatherWing Kit

The Adafruit RGB Matrix FeatherWing Kit is a prototyping add-on that lets makers drive 16, 32 or 64 pixel wide RGB matrices from a Feather board. It targets hobbyists and engineers who want to build animated displays without designing custom driver circuitry.

Two assembly options replace custom wiring

The kit includes a 2x8 IDC shrouded header for top mounting with the matrix cable, or a 2x10 socket header for bottom mounting so the Feather stacks directly on the wing. Choose the top-mount route when you need the Feather accessible for debugging, or the bottom-mount route for a slimmer profile behind the panel.

Works with M0 or M4 Feathers and 5 V DC power

The wing pairs with any Adafruit M0 or M4 Feather running the RGB Matrix library and accepts a 2.1 mm DC jack for a 5 V supply. It frees you from soldering level shifters or power regulators, leaving GPIO pins open for sensors or networking add-ons. Builders who need higher voltage panels or non-Feather hosts will need a different driver solution.

Põhijooned

  • Compatible with 16, 32 or 64 pixel wide RGB matrices
  • Includes 2.1mm DC jack for 5V power supply
  • Works with M0 and M4 based Feather boards
  • Two assembly options for flexible stacking configurations
  • Enables quick project creation with 16 or 32 pixel tall displays

Tehnilised andmed

TypePrototyping Products

Küsimused selle toote kohta

What header style fits the 2x8 IDC cable supplied with a 16x32 or 32x32 RGB matrix?

Solder the 2x8 shrouded IDC header on the top of the FeatherWing so the ribbon cable from the matrix plugs straight in.

Which stacking order avoids the most common soldering mistake on this FeatherWing?

Decide before soldering: header on top for cable connection, or 2x10 socket on bottom to stack the Feather above; mixing them up requires desoldering.

When must the 2.1 mm DC jack be used instead of powering through the Feather?

Use the on-board 2.1 mm jack for a 5 V supply when driving 32-pixel tall matrices such as 32x32 or 64x32 panels.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.