Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Four black sparkle brass fittings for 12mm rigid tubing

Bitspower

Bitspower BP-BSEMLA12-4P 12mm OD rigid tubing fittings 4-pack

SKU CH-ZG1R-WDP3Q MPN BP-BSEMLA12-4P

Four G1/4" brass compression fittings for 12mm OD rigid tubing in a Black Sparkle finish

  • TypeFittings
  • Multi-link design enables complex routing via G1/4" threads
  • High-quality brass construction resists corrosion for long-term loop reliability
  • Compression mechanism secures 12mm OD rigid tubing without leaks
  • Black Sparkle finish matches premium build aesthetics
  • Four-pack value covers multiple connection points in one purchase

Multi-Link Fittings for 12mm OD Hard Tubing

This four-pack of Bitspower G1/4" compression fittings is built for custom liquid-cooling loops that use 12mm outer-diameter rigid tubing. The brass construction and Black Sparkle finish suit enthusiasts assembling a clean, monochrome build. Each fitting accepts a single hard-tube run and threads into any standard G1/4" port on blocks, radiators or reservoirs.

Replaces Standard Single-Connection Fittings

The multi-link design lets you join tubing segments in a straight line without adding extra angled adapters, reducing potential leak points and visual clutter. The upgrade is worthwhile when you need to span longer distances between components or want a cleaner tube run than two separate fittings and a coupler can provide. Builders staying with soft tubing or smaller diameters will not benefit from this specific fitting.

Straightforward Compression Install

Slide the compression nut and olive onto the cut tube, press the tube fully into the fitting body, then hand-tighten the nut before a final quarter-turn with a wrench. The most common issue is an uneven tube cut that prevents a complete seat, causing a slow weep under pressure. Deburring the inside and outside edges and double-checking insertion depth before tightening eliminates the problem.

Põhijooned

  • Multi-link design enables complex routing via G1/4" threads
  • High-quality brass construction resists corrosion for long-term loop reliability
  • Compression mechanism secures 12mm OD rigid tubing without leaks
  • Black Sparkle finish matches premium build aesthetics
  • Four-pack value covers multiple connection points in one purchase

Tehnilised andmed

TypeFittings

Küsimused selle toote kohta

What outer-diameter rigid tubing is required for these G1/4" multi-link fittings?

The fittings are designed for 12mm OD hard tubing, so you must use tubing with that exact outside diameter.

How do you install the compression ring so the seal holds on hard tubing?

Slide the nut and compression ring onto the tube, push the tube fully into the fitting body, then tighten the nut by hand plus a quarter turn with a wrench; skipping the full insertion step causes leaks.

When should the O-rings inside these brass fittings be replaced?

Inspect the O-rings whenever you disassemble the loop; replace them if they show flattening, cracking or loss of elasticity, typically after several thermal cycles.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.