Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Four black sparkle brass fittings for 12mm rigid tubing

Bitspower

Bitspower BP-BSEMLA12-4P 12mm OD rigid tubing fittings 4-pack

SKU CH-ZG1R-WDP3Q MPN BP-BSEMLA12-4P

Four G1/4" brass compression fittings for 12mm OD rigid tubing in a Black Sparkle finish

  • TypeFittings
  • Multi-link design enables complex routing via G1/4" threads
  • High-quality brass construction resists corrosion for long-term loop reliability
  • Compression mechanism secures 12mm OD rigid tubing without leaks
  • Black Sparkle finish matches premium build aesthetics
  • Four-pack value covers multiple connection points in one purchase

Multi-Link Fittings for 12mm OD Hard Tubing

This four-pack of Bitspower G1/4" compression fittings is built for custom liquid-cooling loops that use 12mm outer-diameter rigid tubing. The brass construction and Black Sparkle finish suit enthusiasts assembling a clean, monochrome build. Each fitting accepts a single hard-tube run and threads into any standard G1/4" port on blocks, radiators or reservoirs.

Replaces Standard Single-Connection Fittings

The multi-link design lets you join tubing segments in a straight line without adding extra angled adapters, reducing potential leak points and visual clutter. The upgrade is worthwhile when you need to span longer distances between components or want a cleaner tube run than two separate fittings and a coupler can provide. Builders staying with soft tubing or smaller diameters will not benefit from this specific fitting.

Straightforward Compression Install

Slide the compression nut and olive onto the cut tube, press the tube fully into the fitting body, then hand-tighten the nut before a final quarter-turn with a wrench. The most common issue is an uneven tube cut that prevents a complete seat, causing a slow weep under pressure. Deburring the inside and outside edges and double-checking insertion depth before tightening eliminates the problem.

Helstu kostir

  • Multi-link design enables complex routing via G1/4" threads
  • High-quality brass construction resists corrosion for long-term loop reliability
  • Compression mechanism secures 12mm OD rigid tubing without leaks
  • Black Sparkle finish matches premium build aesthetics
  • Four-pack value covers multiple connection points in one purchase

Tæknilýsing

TypeFittings

Spurningar um þessa vöru

What outer-diameter rigid tubing is required for these G1/4" multi-link fittings?

The fittings are designed for 12mm OD hard tubing, so you must use tubing with that exact outside diameter.

How do you install the compression ring so the seal holds on hard tubing?

Slide the nut and compression ring onto the tube, push the tube fully into the fitting body, then tighten the nut by hand plus a quarter turn with a wrench; skipping the full insertion step causes leaks.

When should the O-rings inside these brass fittings be replaced?

Inspect the O-rings whenever you disassemble the loop; replace them if they show flattening, cracking or loss of elasticity, typically after several thermal cycles.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.