Přijímáme kryptoměny — takže to, co držíte, můžete utratit za skutečný hardware.Plaťte kryptem, utrácejte ho za skutečný hardware. Pojištěná doprava zdarma po celém světě nad 399 $. Neutrální přepravní krabice bez loga, odesílané z Německa.Pojištěná doprava zdarma nad 399 $. Jakmile se otevře pokladna, je váš kurz zablokovaný na 30 minut.Kurz zablokovaný na 30 minut. Každý výrobek je zapečetěný, jeho sériové číslo je zkontrolované a vztahuje se na něj 24měsíční záruka.Zapečetěno, záruka 24 měsíců.

Sledované položky Přihlásit se
Four black sparkle brass fittings for 12mm rigid tubing

Bitspower

Bitspower BP-BSEMLA12-4P 12mm OD rigid tubing fittings 4-pack

SKU CH-ZG1R-WDP3Q MPN BP-BSEMLA12-4P

Four G1/4" brass compression fittings for 12mm OD rigid tubing in a Black Sparkle finish

  • TypeFittings
  • Multi-link design enables complex routing via G1/4" threads
  • High-quality brass construction resists corrosion for long-term loop reliability
  • Compression mechanism secures 12mm OD rigid tubing without leaks
  • Black Sparkle finish matches premium build aesthetics
  • Four-pack value covers multiple connection points in one purchase

Multi-Link Fittings for 12mm OD Hard Tubing

This four-pack of Bitspower G1/4" compression fittings is built for custom liquid-cooling loops that use 12mm outer-diameter rigid tubing. The brass construction and Black Sparkle finish suit enthusiasts assembling a clean, monochrome build. Each fitting accepts a single hard-tube run and threads into any standard G1/4" port on blocks, radiators or reservoirs.

Replaces Standard Single-Connection Fittings

The multi-link design lets you join tubing segments in a straight line without adding extra angled adapters, reducing potential leak points and visual clutter. The upgrade is worthwhile when you need to span longer distances between components or want a cleaner tube run than two separate fittings and a coupler can provide. Builders staying with soft tubing or smaller diameters will not benefit from this specific fitting.

Straightforward Compression Install

Slide the compression nut and olive onto the cut tube, press the tube fully into the fitting body, then hand-tighten the nut before a final quarter-turn with a wrench. The most common issue is an uneven tube cut that prevents a complete seat, causing a slow weep under pressure. Deburring the inside and outside edges and double-checking insertion depth before tightening eliminates the problem.

Přednosti

  • Multi-link design enables complex routing via G1/4" threads
  • High-quality brass construction resists corrosion for long-term loop reliability
  • Compression mechanism secures 12mm OD rigid tubing without leaks
  • Black Sparkle finish matches premium build aesthetics
  • Four-pack value covers multiple connection points in one purchase

Specifikace

TypeFittings

Otázky k tomuto produktu

What outer-diameter rigid tubing is required for these G1/4" multi-link fittings?

The fittings are designed for 12mm OD hard tubing, so you must use tubing with that exact outside diameter.

How do you install the compression ring so the seal holds on hard tubing?

Slide the nut and compression ring onto the tube, push the tube fully into the fitting body, then tighten the nut by hand plus a quarter turn with a wrench; skipping the full insertion step causes leaks.

When should the O-rings inside these brass fittings be replaced?

Inspect the O-rings whenever you disassemble the loop; replace them if they show flattening, cracking or loss of elasticity, typically after several thermal cycles.

Také v této kategorii

Zákazníci také porovnávali

Stejná kategorie, stejná pokladna — osm měn a kurz zamčený na 30 minut.