Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse

EZ Dupe, Inc.

EZ Dupe, Inc. H11HSATB 1-to-11 SATA Duplicator

SKU CH-TFS8-FJK3B

Standalone SATA duplicator copies up to 11 drives at 150 MB/s with four copy and four erase modes including DoD 5220.22 standards

  • TypeHard Drive Duplicator
  • Panel ColorBlack
  • Operating TypeStandalone
  • Display16 x 2 LCD
  • ConnectorSATA
  • Target1 to 11

Target 1 to 11

Data Transfer Rate 150MB/s

Läbikriipsutatud versioonid on olemas, kuid neid pole siin saadaval.

  • Copy 11 drives simultaneously at 150 MB/s per slot
  • Four copy modes include quick, full, partitioned and percentage copy
  • Four erase modes include quick, full, DoD 3-pass and DoD 7-pass
  • Supports 2.5" and 3.5" SATA drives without adapters
  • Standalone operation with 16×2 LCD and 128 MB buffer

Duplication capacity and standalone operation

The duplicator copies one source drive to as many as eleven target drives simultaneously using SATA connectors for both 2.5 and 3.5 inch hard disks and solid state drives. Operation is completely standalone with a sixteen by two LCD and indicator lights, so no host computer or software is required during the copy or erase process.

Sustained throughput and erase compliance

Each target slot maintains a transfer rate of one hundred fifty megabytes per second, which equals nine gigabytes per minute, across all eleven ports during extended duplication runs. Four erase modes are available including three pass and seven pass methods that follow the 5220.22 standard for defence grade sanitisation.

Power and drive preparation checklist

Verify that the installation site can supply alternating current between one hundred fifteen and two hundred thirty volts at fifty or sixty hertz. Confirm that every source and target drive uses a SATA interface and fits the 2.5 or 3.5 inch form factor, because no adapter is included for other connector types.

Põhijooned

  • Copy 11 drives simultaneously at 150 MB/s per slot
  • Four copy modes include quick, full, partitioned and percentage copy
  • Four erase modes include quick, full, DoD 3-pass and DoD 7-pass
  • Supports 2.5" and 3.5" SATA drives without adapters
  • Standalone operation with 16×2 LCD and 128 MB buffer

Tehnilised andmed

BrandEZ Dupe
TypeHard Drive Duplicator
ModelH11HSATB
Part NumberH11HSATB
Panel ColorBlack
Operating TypeStandalone
Display16 x 2 LCD
ConnectorSATA
Target1 to 11
Buffer Memory128M
ControllerAthena Controller
Supported MediaSATA Hard Drive Disk / SATA Solid State Drives
Data Transfer Rate150MB/s
Load TypeSlot
Key FeaturesDuplication
FeaturesIndication Lights
Power SupplyAC: 115-230 V, 50/60 Hz

Selle mudeli teised versioonid

5 veel samast sarjast

Sama seeria, erinev mälumaht, jahutus või taktsagedus — võrrelge enne otsustamist.

Küsimused selle toote kohta

How loud or hot does the H11HSATB get when running all 11 bays at 150 MB/s for hours?

The duplicator is a standalone unit with an AC 115-230 V, 50/60 Hz power supply; no fan noise or thermal figures are published.

What must I already own so the duplicator can copy drives right away?

You need a master SATA drive and up to 11 target SATA 3.5" or 2.5" drives; no computer, software or adapter is required.

Will the Athena Controller work with older SATA I or II drives I still keep?

The controller accepts any SATA-interfaced 3.5" or 2.5" HDD or SSD without an adapter; legacy SATA revisions are supported.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.