Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään

EZ Dupe, Inc.

EZ Dupe, Inc. H11HSATB 1-to-11 SATA Duplicator

SKU CH-TFS8-FJK3B

Standalone SATA duplicator copies up to 11 drives at 150 MB/s with four copy and four erase modes including DoD 5220.22 standards

  • TypeHard Drive Duplicator
  • Panel ColorBlack
  • Operating TypeStandalone
  • Display16 x 2 LCD
  • ConnectorSATA
  • Target1 to 11

Target 1 to 11

Data Transfer Rate 150MB/s

Yliviivatut versiot ovat olemassa, mutta niitä ei ole varastossa täällä.

  • Copy 11 drives simultaneously at 150 MB/s per slot
  • Four copy modes include quick, full, partitioned and percentage copy
  • Four erase modes include quick, full, DoD 3-pass and DoD 7-pass
  • Supports 2.5" and 3.5" SATA drives without adapters
  • Standalone operation with 16×2 LCD and 128 MB buffer

Duplication capacity and standalone operation

The duplicator copies one source drive to as many as eleven target drives simultaneously using SATA connectors for both 2.5 and 3.5 inch hard disks and solid state drives. Operation is completely standalone with a sixteen by two LCD and indicator lights, so no host computer or software is required during the copy or erase process.

Sustained throughput and erase compliance

Each target slot maintains a transfer rate of one hundred fifty megabytes per second, which equals nine gigabytes per minute, across all eleven ports during extended duplication runs. Four erase modes are available including three pass and seven pass methods that follow the 5220.22 standard for defence grade sanitisation.

Power and drive preparation checklist

Verify that the installation site can supply alternating current between one hundred fifteen and two hundred thirty volts at fifty or sixty hertz. Confirm that every source and target drive uses a SATA interface and fits the 2.5 or 3.5 inch form factor, because no adapter is included for other connector types.

Kohokohdat

  • Copy 11 drives simultaneously at 150 MB/s per slot
  • Four copy modes include quick, full, partitioned and percentage copy
  • Four erase modes include quick, full, DoD 3-pass and DoD 7-pass
  • Supports 2.5" and 3.5" SATA drives without adapters
  • Standalone operation with 16×2 LCD and 128 MB buffer

Tekniset tiedot

BrandEZ Dupe
TypeHard Drive Duplicator
ModelH11HSATB
Part NumberH11HSATB
Panel ColorBlack
Operating TypeStandalone
Display16 x 2 LCD
ConnectorSATA
Target1 to 11
Buffer Memory128M
ControllerAthena Controller
Supported MediaSATA Hard Drive Disk / SATA Solid State Drives
Data Transfer Rate150MB/s
Load TypeSlot
Key FeaturesDuplication
FeaturesIndication Lights
Power SupplyAC: 115-230 V, 50/60 Hz

Tämän mallin muut versiot

5 lisää samasta mallistosta

Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.

Kysymyksiä tästä tuotteesta

How loud or hot does the H11HSATB get when running all 11 bays at 150 MB/s for hours?

The duplicator is a standalone unit with an AC 115-230 V, 50/60 Hz power supply; no fan noise or thermal figures are published.

What must I already own so the duplicator can copy drives right away?

You need a master SATA drive and up to 11 target SATA 3.5" or 2.5" drives; no computer, software or adapter is required.

Will the Athena Controller work with older SATA I or II drives I still keep?

The controller accepts any SATA-interfaced 3.5" or 2.5" HDD or SSD without an adapter; legacy SATA revisions are supported.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.