Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Black standalone SATA duplicator with 16 x 2 LCD and three drive slots

EZ Dupe, Inc.

EZ Dupe, Inc. H03HSATB 1-to-3 SATA duplicator

SKU CH-B3WM-QV2AN

Standalone SATA duplicator copies one drive to three at 150 MB/s with four copy modes and four DoD-compliant erase modes

  • TypeHard Drive Duplicator
  • Panel ColorBlack
  • Operating TypeStandalone
  • Display16 x 2 LCD
  • ConnectorSATA
  • Target1 to 3

Target 1 to 3

Data Transfer Rate 150MB/s

Yliviivatut versiot ovat olemassa, mutta niitä ei ole varastossa täällä.

  • Copies up to 3 SATA drives simultaneously at 150MB/s
  • Four duplication modes including quick copy and full media copy
  • Four erase modes including DoD 3-pass and 7-pass standards
  • Standalone operation with 16×2 LCD and no host computer required
  • Supports both 2.5" and 3.5" SATA drives without adapters

Standalone SATA Duplicator

The EZ Dupe H03HSATB is a standalone hard-drive duplicator and sanitiser that copies one SATA source drive to up to three target drives without a host computer. It accepts both 3.5-inch and 2.5-inch SATA hard disks and solid-state drives directly in its slot-load bays. A 16 x 2 LCD panel and indicator lights show job progress and status. The unit runs on 115-230 V AC power at 50 or 60 Hz and includes 128 MB of buffer memory driven by an Athena controller.

IT teams and forensic labs needing secure.

This duplicator suits IT departments, data-recovery specialists and forensic examiners who must clone or erase SATA drives in a controlled, air-gapped environment. Four copy modes — Quick Copy, Whole Media, All Partitioned and Percentage Copy — handle defined and undefined file systems. Four erase modes, including DoD 3-pass and 7-pass to the 5220.22-M standard, meet strict sanitisation policies. Buyers who need to duplicate more than three targets simultaneously or who require interfaces other than SATA should consider other equipment.

150 MB/s maximum copy speed per slot

The specification that determines suitability is the 150 MB/s data transfer rate, equivalent to 9 GB per minute, sustained independently on each of the three target ports. This throughput lets a full 1 TB SATA drive clone in roughly two hours per slot. If your workflow demands higher per-port bandwidth or support for non-SATA media, this model will not meet that requirement.

Kohokohdat

  • Copies up to 3 SATA drives simultaneously at 150MB/s
  • Four duplication modes including quick copy and full media copy
  • Four erase modes including DoD 3-pass and 7-pass standards
  • Standalone operation with 16×2 LCD and no host computer required
  • Supports both 2.5" and 3.5" SATA drives without adapters

Tekniset tiedot

BrandEZ Dupe
TypeHard Drive Duplicator
ModelH03HSATB
Part NumberH03HSATB
Panel ColorBlack
Operating TypeStandalone
Display16 x 2 LCD
ConnectorSATA
Target1 to 3
Buffer Memory128M
ControllerAthena Controller
Supported MediaSATA Hard Drive Disk / SATA Solid State Drives
Data Transfer Rate150MB/s
Load TypeSlot
Key FeaturesDuplication
FeaturesIndication Lights
Power SupplyAC: 115-230 V, 50/60 Hz

Tämän mallin muut versiot

5 lisää samasta mallistosta

Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.

Kysymyksiä tästä tuotteesta

How do I install drives into the H03HSATB duplicator and which step is often missed?

Insert up to three SATA 3.5" or 2.5" drives directly into the slot-load bays; the step often missed is setting the correct copy mode — Quick Copy, Whole Media, All Partitioned or Percentage Copy — before pressing start.

What maintenance or replacement will the H03HSATB need over time?

The unit has no user-serviceable parts; keep the slot openings clear of dust and verify the 128M buffer and Athena Controller operate normally — if a drive bay fails, the whole duplicator requires service.

What limit appears first during sustained high-speed duplication on the H03HSATB?

The 150MB/s per-slot transfer rate is the ceiling; sustained runs at that speed are bounded by the 128M buffer and the Athena Controller throughput, so thermal throttling or buffer saturation will show up before the 115-230 V AC supply becomes a factor.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.